Technical Specifications; Regulatory Compliance - Clarity C120 User Manual

REGULATORY COMPLIANCE

g) This telephone equipment is
notintended to be repaired and it
contains no repairable parts.
Opening the equipment or any
attempt to perform repairs will
oid the warranty. For service or
repairs, call 1-800-552-3368.
h) Connection to party line service
is subject to state tariffs. Contact the
state public utility commission, public
service commission or corporation
commission for information.
i) If your home has specially wired
alarm equipment connected to the
telephone line, ensure the installation
of this telephone equipment does
not disable your alarm equipment.
If you have questions about what
will disable alarm equipment, consult
your telephone company or a
qualified installer.
Customer-Owned Coin/Credit
Card Phones:
To comply with state tariffs, the
telephone company must be given
notification prior to connection. In
some states, the state public utility
commission, public service commis-
sion or corporation commission
must give prior approval
of connection.
Part 15 of FCC Rules
Information
This device complies with Part 15 of
the FCC Rules. Operation is subject
to the following two conditions: (1)
This device may not cause harmful
interference, and (2) this device must
accept any interference received,
including interference that may cause
undesired operation.
Your equipment has been tested and
found to comply with the limits of
a Class B digital device, pursuant to
Part 15 of FCC rules.These limits
are designed to provide reasonable
protection against harmful interfer-
ence in residential installation.
This equipment generates, uses and
can radiate radio frequency energy
and, if not installed and used in
accordance with the instructions,
may cause harmful interference to
radio communications. However,
there is no guarantee that interfer-
ence will not occur in a particular
installation; if this equipment does
cause harmful interference to radio
or television reception, which can be
determined by turning the equipment
off and on, you are encouraged to try
to correct the interference by one of
the following measures:
1. Where it can be done safely,
reorient the receiving television
or radio antenna.
2. To the extent possible, relocate
the television, radio or other
REGULATORY COMPLIANCE
receiver with respect to the
telephone equipment. (This
increases the separation between
the telephone equipment and
the receiver.)
3. Connect the telephone equip-
ment into an outlet on a circuit
different from that to which the
television, radio, or other receiver
is connected.
4. Consult the dealer or an experi-
enced Radio/TV Technician
for help.
CAUTION: Changes or modifica-
tions not expressly approved by the
manufacturer responsible for compli-
ance could void the user's authority
to operate the equipment.
Industry Canada Technical
Specifications
This product meets the
applicable Industry Canada
technical specifications.
Before installing this equipment, users
should ensure that it is permissible
to be connected to the facilities of
the local telecommunications com-
pany.The equipment must also be
installed using an acceptable method
of connection. In some cases, the
company's inside wiring associated
with a single line individual service
may be extended by means of a
certified connector assembly (tele-
phone extension cord).The customer
should be aware that compliance
18 19
with the above conditions may not
prevent degradation of service in
some situations. Repairs to certified
equipment should be made by an
authorized Canadian maintenance
facility designated by the supplier.
Any repairs or alterations made by
the user to this equipment, or equip-
ment malfunctions, may give the
telecommunications company cause
to request the user to disconnect
the equipment.
Users should ensure for their own
protection that the electrical ground
connections of the power utility,
telephone lines and internal metallic
water pipe system, if present, are
connected together.This precaution
may be particularly important in
rural areas.
CAUTION: Users should not
attempt to make such connections
themselves, but should contact
the appropriate electrical inspec-
tion authority, or electrician, as
appropriate.
The Ringer Equivalence Number
is an indication of the maximum
number of terminals allowed to be
connected to a telephone interface.
The termination on an interface
may consist of any combination of
devices subject only to the require-
ment that the sum of the Ringer
Equivalence Numbers of all the
devices does not exceed five.