Initial Auto Installation; Auto Installation; Programme Setup; Selecting A Preset Av Mode - Sharp AQUOS LC-32M450M Operation Manual

Initial auto installation

When the TV powers on for the first time after
purchase, the initial auto installation wizard appears.
Follow the menus and make the necessary settings
one after another.
1
Press POWER on the TV.
• The initial auto installation wizard appears.
2
Press a/b/c/d to select the desired
language, and then press ENTER.
3
Press c/d to select "HOME" or "STORE", and
then press ENTER.
Press a/b to select the desired sound system,
and then press ENTER.
• Auto installation will be executed.
• You do not need to do anything during the auto
search.
NOTE
• HOME mode: Settings are optimised for normal home
viewing and energy efficiency.
• STORE mode: Settings are designed for maximum impact
in retail store displays.
• To change the STORE mode to HOME mode, please refer
to page 12 to reset the unit.

Auto installation

You can run auto installation again, even after setting
up the preset channels.
1
Press MENU and the MENU screen displays.
2
Press c/d to select "Setup".
3
Press a/b to select "Auto installation", and
then press ENTER.
4
If you have already set the password, enter it
here.
• See page 11 for setting a password.
5
Press c/d to select "Yes", and then press
ENTER.
6
Press a/b/c/d to select the desired
language listed on the screen, and then press
ENTER.
Press a/b to select the desired sound system,
and then press ENTER.
You do not need to do anything during the auto
search. Press MENU to exit.

Programme setup

Auto search
You can also automatically search by performing
the procedure below. This is the same function as
programme auto search in auto installation.
1
Press MENU and the MENU screen displays.
2
Press c/d to select "Setup".
3
Press a/b to select "Programme setup", and
then press ENTER.
4
If you have already set the password, enter it
here.
• See page 11 for setting a password.
5
Press a/b to select "Auto search", and then
press ENTER.
6
Press c/d to select "Yes", and then press
ENTER.
Press a/b to select the desired sound system,
and then press ENTER.
You do not need to do anything during the auto
search. Press MENU to exit.
Manual adjust
You can set some channel item manually.
1
Repeat steps 1 to 4 in Auto search.
2
Press a/b to select "Manual adjust", and then
press ENTER.
3
Press c/d to select "Yes", and then press
ENTER.
4
Press a/b/c/d to select the channel you
want to edit, and then press ENTER.
• The selected channel information displays.
5
Press a/b to select the desired menu, and
then press ENTER.
Press a/b or c/d to select the desired item
6
or adjust the item to the desired level. Press
ENTER if necessary.
H Search
The next channel will be search in order.
H Fine
You can adjust the frequency to your desired
position.
NOTE
• Adjust while checking the background picture as a
reference.
• Instead of pressing c/d to adjust the frequency, you
can set by directly entering the frequency number of the
channel with 0 — 9.
a
• 179.25 MHz: Press 1 s 7 s 9 s 2 s 5.
• 49.25 MHz: Press 4 s 9 s 2 s 5 s ENTER.
Programme setup (Continued)
H Colour system
Select the optimum colour system to receive. (Auto,
PAL, SECAM, NTSC 3.58, NTSC 4.43, PAL-60)
H Sound system (Broadcasting system)
Select the optimum sound system (Broadcasting
system) to receive. (B/G, D/K, I, M)
H Label
To enter the name of the channel. Maximum 5
alphanumeric can be input.
Press a/b/c/d to select each character of the
new name for the channel, and then press ENTER.
Repeat until the name is fully spelt out.
• When you want to set a channel name of less than 5
characters, select "END".
H Booster
Enhance the picture quality during weak signal. It is
not recommended to turn on during strong signal
condition. It may induced unwanted noise. (On, Off)
H Skip
Channels with "Skip" set to "On" are passed over
when using CHr/s even if selected while
watching the image from the TV. (On, Off)
H Lock
You can block the viewing of any channel. (On, Off)
NOTE
• See "Child lock" for setting a password.
• If "Lock" is set to "On" for a channel, "Child lock has been
activated." is displayed when you select the channel, and
the image and sound of the channel is blocked.
• When pressing ENTER while "Child lock has been
activated." is displayed, password input menu will be
displayed. Inputting the correct password lifts the child
lock temporarily until the power is turned off.
Sort
Channel position can be sorted freely.
1
Repeat steps 1 to 4 in Auto search.
2
Press a/b to select "Sort", and then press
ENTER.
3
Press c/d to select "Yes", and then press
ENTER.
4
Press a/b/c/d to select the channel you
want to move, and then press ENTER.
5
Move it to the desired position by pressing
a/b/c/d, and then press ENTER.
6
Repeat the steps 4 and 5 until all desired
channels are sorted.
7 8
Erase programme
The individual programme can be erased.
1
Repeat steps 1 to 4 in Auto search.
2
Press a/b to select "Erase programme", and
then press ENTER.
3
Press c/d to select "Yes", and then press
ENTER.
4
Press a/b/c/d to select the channel you
want to erase, and then press ENTER.
5
Press ENTER to erase the channel.
6
Repeat the steps 4 and 5 until all desired
channels are erased.

Selecting a preset AV mode

"AV mode" gives you several viewing options to
choose from to best match the system environment,
which can vary due to factors like room-brightness,
type of programme watched or the type of image
input from external equipment.
1
Press AV MODE.
2
Each time you press AV MODE, the mode
changes.
• You can also switch the mode in the "AV mode"
menu on the "Picture" menu screen.
Selected item Description
For a highly defi ned image in a normally
STANDARD
bright room.
MOVIE For a movie.
GAME For game play.
PC For PC. (Available only when inputting an
HDMI or PC signal.)
Allows the user to customise settings as
USER
desired. You can set the mode for each
input source.
DYNAMIC Changes the image and sound settings to
(FIXED) the factory preset values. No adjustments
are allowed.
DYNAMIC For a clear-cut image emphasising high
contrast for sports viewing.
NOTE
• You can select a different AV mode item for each input
mode. (For example, select STANDARD for TV input and
DYNAMIC for VIDEO input.)
• During PC input mode, only "STANDARD", "PC" and
"USER(INPUT7)" can be selected under the AV mode
selection.