Dvc To Dvd Dubbing - Toshiba DVR80KF Owner's Manual

E9TK5FD_EN.book Page 40 Wednesday, January 13, 2010 10:33 AM
7 Status of the current operation and the time
counter
Each icon means (Available icons may vary depending on
the DVC):
DVC is in stop mode.
DVC is in playback mode.
DVC is in pause mode.
DVC is fast forwarding. (standard speed)
DVC is fast forwarding. (faster than above)
DVC is fast forwarding. (faster than above)
DVC is slow forwarding. (standard speed)
DVC is slow forwarding. (faster than above)
DVC is slow forwarding. (faster than above)
DVC is fast forwarding. (in stop mode)
DVC is fast reversing. (in stop mode)
DVC is fast reversing. (standard speed)
DVC is fast reversing. (faster than above)
DVC is fast reversing. (faster than above)
DVC is in slow reverse playback.
DVC is in recording.
DVC is in recording pause mode.
Please also read the operating instructions of your
DVC for more information.

DVC to DVD Dubbing

Video VR
DVD-RW DVD-RW DVD-RW DVD-RW DVD-RW DVD-RW DVD-R DVD-R DVD-R
Before recording from DVC, see page 19 for connection
instructions. (See page 71 for DVC to VHS Dubbing.)
Preparing for DV dubbing (DVC to DVD):
• Insert a recordable DVD.
• Make sure your DVC is in video mode.
Press [DVD] first.
1
Press [INPUT SELECT
the external input channel, then press
[PROG. ] repeatedly to select DV(AV3).
2
Press [REC MODE] to select a recording mode.
(See page 28.)
3
Press [DISPLAY].
40
EN
4
5
6
To stop dubbing:
1) Select "Control" using [K L], then press
2) Select "DVD" using [K L], then press
3) Press [STOP C].
Note
DVD+RW DVD+RW DVD+RW DVD+R DVD+R DVD+R
• The tape will rewind a few seconds when you press
• The unit does not send out the output signal to DVC.
• For the proper operation, connect DVC to the unit directly.
• Do not connect more than one DVC.
• The unit can only accept DVC. Other DV device such as
• If no video signal is detected from the DVC during DVC to
] repeatedly to select
• When the DVC is in camera mode, refer to "Guide to DV and
• Date / time and cassette memory data will not be recorded.
DV • Pictures with a copy-guard signal cannot be recorded.
AB-1234
• A DV terminal is a terminal that can use the transmission
0:00:00
With "Control" highlighted, press [ENTER OK]
to display the available devices to control with
the remote control of this unit. Select "DVC"
using [K L], then press [ENTER OK].
e.g.) DVC to DVD dubbing
1/ 1 1/ 1
T C
-RW
Control DVD
DV Audio Stereo1
Start Rec
Now you can operate your DVC with the remote control of
this unit.
Press [PLAY B] to start playing back the DVC,
and find where you want to start dubbing.
Press [STOP C] when it comes to the desired
start point.
Select "Start Rec" using [K L], then press
[ENTER OK].
The dubbing will start.
[ENTER OK].
[ENTER OK].
6
[ENTER OK] at step so that the dubbing starts exactly
where you press [PAUSE F] instead of [STOP C] at step
Do not connect this unit and DVC via any other unit.
cable/satellite box or D-VHS recorder cannot be recognised.
DVD dubbing, the recording will be paused and "I" will flash
on the TV screen. The recording will resume when the unit
detects the video signal again.
On-Screen Display" on page 39.
mode conforming to the IEEE 1394 standards called
"Fire Wire". It serves as the interface that connects the PC
and peripheral device such as "i.LINK" (registered trademark
of SONY). It enables digital dubbing between DV devices
with little degradation.
VR ORG
DV
AB-1234
0:00:00
SP 2:00
5
.