1. Manuals
  2. Brands
  3. Central Pneumatic Manuals
  4. Nail Gun
  5. Contractor 97526
  6. Assembly and operating instructions manual

Central Pneumatic CENTRALPNEUMATIC 97526 Assembly And Operating Instructions Manual

Air pin nailer 23-gauge
Hide thumbs Also See for CENTRALPNEUMATIC 97526:
Table of Contents

Advertisement

Quick Links

ASSEMBLY AND OPERATING INSTRUCTIONS
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
©
Copyright
2007 by Harbor Freight Tools
contained herein may be reproduced in any shape or form without the express written consent of
Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein. Tools required for
assembly and service may not be included.
For technical questions or replacement parts, please call 1-800-444-3353.
Revised Manual 10g
AIR PIN NAILER
23-GAUGE
Model
®
. All rights reserved. No portion of this manual or any artwork
97526

Advertisement

Table of Contents
loading

Related Manuals for Central Pneumatic CENTRALPNEUMATIC 97526

Summary of Contents for Central Pneumatic CENTRALPNEUMATIC 97526

  • Page 1 Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein. Tools required for assembly and service may not be included.

  • Page 2: Specifications

    SPECIFICATIONS Fastener Type/Gauge Headless Pins, 23 Gauge Magazine Capacity 100 Pins Operating Pressure 60-100 PSI; 120 PSI Max. Air Consumption 5.5 CFM @ 90 PSI Air Inlet 1/4” - 18 NPT Pin Length Settings 1/2”, 5/8”, 3/4”, 7/8”, 1’” 1 1/4”-18 NPT Air Coupler 1 3mm Hex Wrench Accessories 1 4mm Hex Wrench...
  • Page 3 Avoid accidental starting. Carrying power tools with your finger on the Trigger (27) invites accidents. Be sure all tools and/or attachments used with this Air Nailer are secure before plugging in or turning on the air supply. 10. Be careful when connecting/ disconnecting air supply.

  • Page 4: Specific Safety Rules

    SPECIFIC SAFETY RULES Maintain labels and nameplates on the Air Nailer. These carry important information. If unreadable or missing, contact Harbor Freight Tools for a replacement. Maintain a safe working environment. Make sure there is adequate surrounding workspace. Do not use this product in a damp or wet location.

  • Page 5: Unpacking And Setup

    When unpacking, check to make sure that the item is intact and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible. NOTE: READ ALL INSTRUCTIONS...
  • Page 6 OPERATION INSTRUCTIONS Before use, add a few drops of pneumatic tool oil (not included) into the Inlet. Attach the Air Coupler (61) to Air Inlet using pipe thread seal tape (not included). Then connect the 3/8” Air Source Hose to the Nailer. Set the working air pressure on the regulator to between 60 and 100 PSI.

  • Page 7: Inspection, Maintenance, And Cleaning

    INSPECTION, MAINTENANCE, AND CLEANING WARNING! Make sure air compressor is unplugged and that the Nailer is disconnected from its Air Supply before performing any inspection, maintenance, or cleaning procedures. BEFORE EACH USE, inspect the general condition of this tool. Check for loose screws, misalignment or binding of moving parts, cracked or broken parts, damaged air hoses, and any other condition that may affect its safe operation.

  • Page 8: Parts List

    PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT.

  • Page 9: Assembly Diagram

    ASSEMBLY DIAGRAM SKU 97526 For technical questions, please call 1-800-444-3353. Page 9...
  • Page 10 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.

Table of Contents