Panasonic Digital Palmcorder PV-GS250 Operating Instructions Manual page 25

Digital video camcorder
Hide thumbs Also See for Digital Palmcorder PV-GS250:
Table of Contents

Advertisement

Available languages

Available languages

(14)
Recording start/stop button [START/
STOP] ¢
(15)
Playback button [1]
(16)
Fast forward/cue button [5]
(17)
Enter button [ENTER]
¢ means that these buttons function in the same
manner as the corresponding buttons on the
Camcorder.
ª
Install a button-type battery
Install the button-type battery supplied in the
remote control before using it.
1
While pressing the stopper 1, pull out the
battery holder.
1
2
Set the button-type battery with its (i) mark
facing upward and slide the battery holder
back into place.
Warning
Danger of explosion if battery is
incorrectly replaced.
Replace only with the same or equivalent
type recommended by the equipment
manufacturer. Discard used batteries
according to manufacturer's instructions.
Risk of fire, explosion and burns. Do not
recharge, disassemble, heat above 212°F
(100°C) or incinerate. Keep the Button-
Type battery out of the reach of children.
Never put Button-Type battery in mouth.
If swallowed, call your doctor.
Replace battery with Panasonic PART NO.
CR2025 only. Use of another battery may
present a risk of fire or explosion.
Caution: Battery may explode if mistreated.
Dispose of used battery promptly. Keep
away from children.
Do not recharge, disassemble or dispose of
in fire.
Before using
-22-
ª
Remote control usable range
≥The distance between the remote control and
the Camcorder: Within approx. 15 feet (5 m)
Angle: Approx. 10o up and 15o down, left, and
right
ª
Selecting the remote control mode
If 2 Camcorders are used simultaneously, set the
mode for one pair of Camcorder and remote
control to [VCR1] and that of the other pair to
[VCR2]. This will prevent interference between
the 2 pairs. (The default setting is [VCR1]. When
the button-type battery is replaced, the setting will
revert to the default [VCR1].)
1
Setting on the Camcorder:
Set [SETUP] >> [REMOTE] >> [VCR1] or
[VCR2].
2
Setting on the remote control:
STILL ADV
2
[VCR1]:
Press [D] and [∫] simultaneously. 1
[VCR2]:
Press [E] and [∫] simultaneously. 2
ª
Concerning the button-type battery
≥When the button-type battery runs down, replace
it with a new battery (part number: CR2025). The
battery is normally expected to last about 1 year,
but it depends on operation frequency.
≥Keep the button-type battery out of the reach of
children.
≥If the remote control mode of the Camcorder
and that of the remote control do not match with
each other, "REMOTE" will appear. When the
remote control is operated for the first time after
the Camcorder is turned on, "CHECK REMOTE
MODE" (
) will appear and operation is
-67-
impossible. Set the same remote control mode.
≥The remote control is intended for indoor
operation. Outdoors or under strong light, the
Camcorder may not operate properly even
within the usable ranges.
≥Within a 3 feet (1 m) range, you can operate the
remote control using the remote control sensor
on the LCD monitor side of the Camcorder.
VOL
PAUSE STILL ADV
1
STOP
VAR
LSQT0862
25

Hide quick links:

Advertisement

Table of Contents
loading

This manual is also suitable for:

Pv-gs250 - 3.1mp 3ccd minidv camcorder

Table of Contents