Changing The Main Unit And Remote Control Mode - Panasonic SC-EN35DB Operating Instructions Manual

DAB (continued)
Checking the DAB signal quality
To improve reception by adjusting the antenna while monitoring signal quality on the
display.
 Press [DAB MENU] to enter menu mode.
Note
"SCAN FAILED" appears if no stations are memorized. If this occurs, adjust the
antenna and try Auto scanning or change the Auto scan frequency range.
 Within 10 seconds, press [ALBUM
"SIGNAL QUALITY" and then press [ENTER].
DAB
 Press [ALBUM or ] to select the frequency.
DAB
Frequency block Frequency
DAB
Reception quality
0 (poor) - 8 (excellent)
To exit
Press [DAB MENU] again.
Note
In order to enjoy the new stations after adjusting the antenna, it is necessary to
perform Auto scanning and update the station memory.
Changing the Auto scan frequency range
Only the frequencies currently used in the UK as of March 2007 on BAND III are Auto
scanned ("United Kingdom", factory setting).
Select "ALL BAND III" when you want to store stations on other frequencies to
memory.
 Press [DAB MENU] to enter menu mode.
 Within 10 seconds, press [ALBUM
"DAB SCAN MODE" and then press [ENTER].
DAB
DAB
 Within 10 seconds, press [ALBUM
KINGDOM" or "ALL BAND III" and then press [ENTER].
DAB
Auto scan begins automatically after the change has been made.
To exit
Press [DAB MENU] again.
Note
When the "DAB SCAN MODE" is changed, the DAB preset channels are erased and if
the DAB play timer has been set the timer switches to off.

Changing the main unit and remote control mode

The remote control and main unit are factory-set to "REMOTE 1" mode.
If your remote control affects other equipment during operation, you can switch to
operate in "REMOTE 2" mode.
To switch to "REMOTE 2" mode
 (While pressing and hold [MUSIC PORT] on the main unit)
Press and hold [2] until "REMOTE 2" appears on the main unit display.
 Press and hold [ENTER] and [2] for at least 2 seconds.
The main unit and remote control are now set to operate in "REMOTE 2" mode.
or ] to select
or ] to select
or ] to select "UNITED
➡ Page 2 for the position of remote control buttons.
ALL BAND III Frequency
Frequency Frequency
block (MHz)
5A 174.928
5B 176.640
5C 178.352
5D 180.064
6A 181.936
6B 183.648
6C 185.360
6D 187.072
7A 188.928
7B 190.640
7C 192.352
7D 194.064
8A 195.936
8B 197.648
8C 199.360
8D 201.072
9A 202.928
9B 204.640
9C 206.352
9D 208.064
10A 209.936
Shaded areas are frequencies used currently as of March 2007 in the "United
Kingdom".
To return to "REMOTE 1" mode
Perform steps 1 and 2 above but use [1] instead of [2] for both steps. ("REMOTE 1"
appears on the main unit during step 1.)
The remote control cannot work with the main unit if their modes are different.
"REMOTE 1" or "REMOTE 2" appears on the main unit when you operate the remote
control.*
* If "REMOTE 1" appears (The main unit is in "REMOTE 1" mode.)
Press and hold [ENTER] and [1] on the remote control for at least 2 seconds.
If "REMOTE 2" appears (The main unit is in "REMOTE 2" mode.)
Press and hold [ENTER] and [2] on the remote control for at least 2 seconds.
Frequency Frequency
block (MHz)
10N 210.096
10B 211.648
10C 213.360
10D 215.072
11A 216.928
11N 217.088
11B 218.640
11C 220.352
11D 222.064
12A 223.936
12N 224.096
12B 225.648
12C 227.360
12D 229.072
13A 230.784
13B 232.496
13C 234.208
13D 235.776
13E 237.488
13F 239.200
7