Table of Contents
Advertisement
Quick Links
2-IN-1 AIR HAMMER
WITH 4 PC CHISELS & NEEDLE SCALER
ASSEMBLY AND OPERATION INSTRUCTIONS
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
©
Copyright
2007 by Harbor Freight Tools
contained herein may be reproduced in any shape or form without the express written consent of
Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein. Tools required for
assembly and service may not be included.
For technical questions or replacement parts, please call 1-800-444-3353.
Revised Manual 11h
Model
Visit our website at: http://www.harborfreight.com
®
. All rights reserved. No portion of this manual or any artwork
95801
Advertisement
Table of Contents
Related Manuals for Central Pneumatic 95801
Summary of Contents for Central Pneumatic 95801
- Page 1 Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein. Tools required for assembly and service may not be included.
-
Page 2: Specifications
Use compressed air only: Clean, dry, regulated compressed air at no more than 90 PSI. Never use oxygen, carbon dioxide, combustible gases, or any other bottled gas as a power source for this tool. SKU 95801 For technical questions, please call 1-800-444-3353. SPECIFICATIONS Overall dimensions: 7-1/4”... - Page 3 Use clamps (not included) or other practical ways to secure and support the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control. SKU 95801 For technical questions, please call 1-800-444-3353. Page 3...
-
Page 4: Specific Safety Rules
SPECIFIC SAFETY RULES Maintain labels and nameplates on the Air Hammer. These carry important in- formation. If unreadable or missing, contact Harbor Freight Tools for a replacement. Maintain a safe working environment. Make sure there is adequate surrounding workspace. Do not use this product in a damp or wet location. - Page 5 § 25249.5, et seq.) When unpacking, check to make sure that the item is intact and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible.
- Page 6 Insert Cylinder (13) over the Plunger (14) and the Valve (15) and carefully twist the Cylinder (13) into the Air Housing (1). Figure 3 13 14 SKU 95801 For technical questions, please call 1-800-444-3353. Figure 2 Front Hook 16 Rear Hook...
- Page 7 Insert the Needles (5A) through the holes in the Needle Holder (4A). There are nineteen Needles. Make sure all holes are filled before putting the Needle Holder (4A) through the Spring (3A), the Retainer Clip (2A) and into the Barrel Assembly SKU 95801 For technical questions, please call 1-800-444-3353. USE AS A SCALER...
- Page 8 WARNING: If the Air Hammer is being used as a Scaler, use a ANSI-approved full face shield and not just safety goggles to protect against Needles that may snap off and could possibly cause personal injury. SKU 95801 For technical questions, please call 1-800-444-3353. Figure 5...
-
Page 9: Inspection, Maintenance, And Cleaning
CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. SKU 95801 For technical questions, please call 1-800-444-3353. MAINTENANCE CHART... -
Page 10: Parts List
AIR HAMMER PARTS: Housing Stopple Bushing Boll Spring Air Inlet Trigger O - Ring Regulator Cylinder Plunger SKU 95801 For technical questions, please call 1-800-444-3353. PARTS LIST Part Description Valve Spring Tools SCRAPER PARTS: Barrel Assembly Retainer Clip Spring Needle Holder... -
Page 11: Assembly Diagrams
ASSEMBLY DIAGRAMS Air Hammer Diagram Scaler Diagram SKU 95801 For technical questions, please call 1-800-444-3353. Page 11... - Page 12 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.