Rear Panel - NAD T 567 Owner's Manual

IDENTIFICATION OF CONTROLS

REAR PANEL

1
ATTENTION!
Please make sure that the T 567 is powered off or unplugged before making any connections. It is also advisable to power down or unplug all associated
components while making or breaking any signal or AC power connections.
1 AC MAINS INPUT
• The T 567 comes supplied with a separate AC Mains cable.
• Before connecting the cable to a live wall socket, ensure first that it
is firmly connected to the T 567's AC Mains input socket.
• Always disconnect the AC Mains cable plug from the live wall socket
first, before disconnecting the cable from the T 567's Mains input
socket.
2 LOCAL AREA NETWORK (LAN) PORT
• Using a commercially available straight LAN cable (Category 5/
CAT5 or better with RJ45 connector), connect this LAN port to the
corresponding port of your modem or router. By connecting the
T 567 to broadband internet, you can playback a disc that offers BD-
Live function.
• Refer also to the "NETWORK SETUP MENU" section of "USING THE
T 567" under the "OPERATION" main heading.
NOTES
• NAD is not responsible for any malfunction of the T 567 and/or the
internet connection due to communication errors or malfunctions
associated with your broadband internet connection or other connected
equipment. Contact your Internet Service Provider (ISP) for assistance or
the service bureau of your other equipment.
• Contact your ISP for policies, charges, content restrictions, service
limitations, bandwidth, repair and other related issues pertinent to
internet connectivity.
• Some disc related material available through internet may not be
compatible with the T 567. Contact the producer of the disc for questions
about such content availability or compatibility.
3 IR IN
This input is connected to the output of an IR (infrared) repeater
(Xantech or similar) or the IR output of another component to allow
control of the T 567 from a remote location. Most NAD products with IR
OUT are fully compatible with the T 567.
10
2 3 4 5 6
4 HDMI OUT
• Using a HDMI cable (not supplied), connect the HDMI OUT jack to
the corresponding HDMI input jack of a compatible equipment like
a HDTV, a projector or an A/V Receiver.
• Dolby TrueHD, Dolby Digital Plus and DTS-HD Master Audio are
supported with maximum 7.1 channels when HDMI OUT is the
selected audio output port.
• Make sure to connect to an amplifier or receiver with a built-in
(Dolby Digital, Dolby Digital Plus, Dolby TrueHD, Dolby Digital Plus,
DTS-HD Master Audio and other applicable formats) decoder to
playback applicable multichannel audio formats.
WARNING
Before connecting and disconnecting any HDMI cables, both the T 567
and the ancillary source must be powered OFF and unplugged from the
AC outlet. Failure to observe this practice may cause permanent damage
to all equipment connected via HDMI sockets.
IMPORTANT NOTICE
If your HDMI equipped TV is not capable of decoding DTS or Dolby
Digital Bitstream, set the T 567's HDMI or Digital Output setting at the
"Audio Setup Menu" to "PCM Stereo". There may be a rushing noise
heard if your TV is not capable of decoding the DTS (or Dolby Digital)
Bitstream; most TVs do not have this capability.
5 DIGITAL AUDIO OUT (COAXIAL, OPTICAL)
• The digital playback audio output signal is available at these ports.
• Connect the optical or coaxial digital OUT ports to the
corresponding S/PDIF digital input of an amplifier, receiver,
computer soundcard or other digital processors.
6 COMPONENT VIDEO OUT
• Connect to the corresponding component video input of a
compatible equipment like a monitor/television, projector, A/V
receiver or processor.
• Be sure to observe consistency in connecting the appropriate Y, Pb,
Pr jacks to the corresponding sources/inputs. Do not rely purely on
the color coding of the jacks, which may not always be consistent
among brands.