Safety Instructions Notational Note These safety instructions must be kept to ensure your safety and prevent property damage. Make sure to read the instructions carefully and use the product in the correct manner. Warning / Caution Otherwise, it may result in death or personal injury. Otherwise, it may result in personal injury or property damage.
Safety Instructions Insert the power plug firmly so that it does not come loose. • A bad connection may cause fire. Do not excessively bend the plug and wire nor place heavy objects upon them, which could cause damage. • This may cause electric shock or fire.
Page 4
Safety Instructions Do not place the product on an unstable or small surface area. • Place the product on an even and stable surface, as the product may fall and cause harm to someone walking by, specifically children. Do not place the product on the floor. •...
Page 5
Safety Instructions Do not spray water or detergent directly onto the monitor. • This may cause damage, electric shock or fire. Use the recommended detergent with a smooth cloth. If the connector between the plug and the pin is dusty or dirty, clean it properly using a dry cloth.
Page 6
Safety Instructions Do not try to move the monitor by pulling only the wire or the signal cable. • This may cause a breakdown, electric shock or fire due to damage to the cable. Do not move the monitor right or left by pulling only the wire or the signal cable.
Page 7
Safety Instructions To ease eye strain, take at least a five-minute break after every hour of using the monitor. Do not install the product on an unstable, uneven surface or a location prone to vibrations. • Dropping the product may cause damage to the product or the person carrying it.
Page 8
Safety Instructions • Keep the angle of the elbow perpendicular. • Keep the angle of the knees at more than 90 degree. Do not let your feet fall up from the floor. Adjust the arm position so that it is below the heart.
Introduction Package Contents Note Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Contact a local dealer to buy optional items. Unpacking Monitor Manuals Quick Setup Guide Warranty Card User's Guide (Not available in all loca- tions) Cables...
Introduction Your Monitor Initial Settings Select the language using the up or down key. The displayed content will disappear after 40 seconds. Turn the Power button off and on. It will be displayed again. It can be displayed up to three (3) times. Make sure to adjust the resolution of your PC before reaching the maximum count.
Page 11
Introduction Note You can configure the customized key for a required function via Setup > Cus- tomized Key. Brightness button [ ] When OSD is not on the screen, push the button to adjust brightness. >> Click here to see an animation clip Adjust buttons [ These buttons allow you to adjust items in the menu.
Page 12
Introduction Note See Connecting Cables for further information regarding cable connections.
Connections Connecting Cables Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. Use a connection appropriate for your computer. Using the D-sub (Analog) connector on the video card. •...
Samsung is not liable for these kinds of accidents. • Samsung is not liable for product damage or personal injury when a non-VESA or non-specified wall mount is used or the consumer fails to follow the product installation instructions.
Prepare a blank disk and download the driver program file at the Internet web site shown here. Internet web site : http://www.samsung.com/ (Worldwide) Installing the Monitor Driver (Automatic) Insert CD into the CD-ROM drive. Click "Windows". Choose your monitor model in the model list, then click the "OK" button.
Using the Software Note This monitor driver is under certifying MS logo, and this installation doesn't damage your system. The certified driver will be posted on Samsung Monitor homepage. http://www.samsung.com/ Installing the Monitor Driver (Manual) ® Microsoft Windows Vista™‚ Operating System Insert your Manual CD into your CD-ROM drive.
Page 17
Note This monitor driver is under certifying MS logo, and this installation doesn't damage your system. The certified driver will be posted on Samsung Monitor homepage. Click "Update Driver..." in the "Driver" tab. Check the "Browse my computer for driver software" checkbox and click "Let me pick from a list of device drivers on my computer".
Page 18
Using the Software Select the model that matches your monitor from the list of monitor models on the screen, and click "Next". 10. Click "Close" ! ’ "Close" ! ’ "OK" ! ’ "OK" on the following screens displayed in sequence. ®...
Page 19
Using the Software Insert CD into the CD-ROM drive. Click "Start" ! ’ "Control Panel" then click the "Appearance and Themes" icon. Click "Display" icon and choose the "Settings" tab then click "Advanced...". Click the "Properties" button on the "Monitor" tab and select "Driver" tab. Click "Update Driver..."...
Page 20
If you can see following message window, then click the "Continue Anyway" button. Then click "OK" button. Note This monitor driver is under certifying MS logo, and this installation doesn't damage your system. The certified driver will be posted on Samsung Monitor homepage. http://www.samsung.com/ Click the "Close" button then click "OK" button continually.
Page 21
Using the Software 10. Monitor driver installation is completed. ® ® Microsoft Windows 2000 Operating System When you can see "Digital Signature Not Found" on your monitor, follow these steps. Choose "OK" button on the "Insert disk" window. Click the "Browse" button on the "File Needed" window. Choose A:(D:\Driver) then click the "Open"...
Page 22
Using the Software Select the "Monitor" tab. Click the "Change" button in the "Monitor Type" area. Choose "Specify the location of the driver". Choose "Display a list of all the driver in a specific location..." then click "Next" button. Click the "Have Disk" button. Specify A:\(D:\driver) then click "OK"...
How to install the Natural Color software Insert the CD included with the Samsung monitor into the CD-ROM Drive. Then, the initial screen of the program Natural Color will be executed. Click Natural Color on the initial screen to install the Natural Color software.
Using the Software Installation Insert the installation CD into the CD-ROM drive. Click the MagicTune™ installation file. Note If the popup window to install the software for the main screen is not displayed, proceed with the installation using the MagicTune executable file on the CD. Select installation Language, Click "Next".
Page 25
Using the Software Uninstall The MagicTune™ program can be removed only by using the "Add or Remove Programs" option of ® the Windows Control Panel. Perform the following steps remove MagicTune™. Go to [Task Tray] ! ’ [ Start] ! ’ [ Settings] and select [Control Panel] in the menu. If the program ®...
Adjusting the Monitor Direct Functions AUTO When the 'AUTO' button is pressed, the auto adjustment screen appears as shown in the animated screen on the center. Auto adjustment allows the monitor to self-adjust to the incoming Analog signal. The values of Fine, Coarse and Position are adjusted automatically.
Page 27
Adjusting the Monitor When pressing the MENU button after locking the OSD This is the function that locks the OSD in order to keep the current states of settings or prevent others from adjusting the current settings. Lock : Hold down the MENU button for more than five (5) seconds to activate the OSD adjustment lock function.
Adjusting the Monitor Note Though the OSD adjustment lock function is activated, you can still adjust the brightness and contrast, and adjust Customized Key ( ) using the Direct button. Customized key You can customize key assignment for the Custom button according to your preferences. To view the operating screen displayed when pressing the [ ] button after configuring the cus- tomized key for a function, click the name of each function.
Adjusting the Monitor Brightness When OSD is not on the screen, push the Brightness ( ) button to adjust brightness. OSD Function Picture Brightness Contrast Magic- Bright Color MagicCol- Color Tone Color Con- Color Effect Gamma trol Image Coarse Fine Sharpness H-Position V-Posi-...
Page 30
Adjusting the Monitor You can use the on-screen menus to change the brightness according to personal preference. MENU ! ’ ! ’ ! ’ ! ’ MENU Contrast (Not available in MagicBright mode of Dynamic Contrast.) You can use the on-screen menus to change the contrast according to personal preference. ( Not available in MagicColor mode of Full and Intelligent.
Page 31
Adjusting the Monitor MagicBright Push the button to circle through available preconfigured modes. MagicBright is a new feature providing optimum viewing environment depending on the contents of the image you are watching. Currently seven different modes are available: Custom, Text, Internet, Game, Sport, Movie and Dynamic Contrast.
Page 32
Color (Not available in MagicBright mode of Dynamic Contrast.) MagicColor MagicColor is a new technology that Samsung has exclusively developed to improve digital image and to display natural color more clearly without disturbing image quality. • Off - Returns to the original mode.
Adjusting the Monitor Color Tone The tone of the color can be changed and one of four modes can be selected. • Cool - Makes whites bluish. • Normal - Keeps whites white. • Warm - Makes whites reddish. • Custom - Select this mode when you want to adjust the image according to your preferences.
Adjusting the Monitor Color Control Adjusts individual Red, Green, Blue color balance. ( Not available in MagicColor mode of Full and Intelligent. ) MENU ! ’ ! ’ ! ’ ! ’ ! ’ ! ’ ! ’ ! ’ MENU Color Effect You can change the overall mood by changing the screen colors.
Page 35
Adjusting the Monitor • • Grayscale • Green • Aqua • Sepia • Off - This applies an achromatic color to the screen to adjust the screen effects. • Grayscale - The default colors of black and white are displayed. •...
Page 36
Adjusting the Monitor Image Coarse Removes noise such as vertical stripes. Coarse adjustment may move the screen image area. You may relocate it to the center using the horizontal control menu. (Available in Analog mode only) MENU ! ’ ! ’ ! ’...
Page 37
Adjusting the Monitor Fine Removes noise such as horizontal stripes. If the noise persists even after Fine tuning, repeat it after adjusting the frequency (clock speed). (Available in Analog mode only) MENU ! ’ ! ’ ! ’ ! ’ ! ’...
Page 38
Adjusting the Monitor ( Not available in MagicColor mode of Full and Intelligent. ) MENU ! ’ ! ’ ! ’ ! ’ ! ’ ! ’ MENU H-Position Changes the horizontal position of the monitor's entire display. (Available in Analog mode only) MENU ! ’...
Page 39
Adjusting the Monitor Changes the vertical position of the monitor's entire display. (Available in Analog mode only) MENU ! ’ ! ’ ! ’ ! ’ ! ’ ! ’ MENU Language You can choose one of nine languages. Note The language chosen affects only the language of the OSD.
Page 40
Adjusting the Monitor H-Position You can change the horizontal position where the OSD menu appears on your monitor. MENU ! ’ ! ’ ! ’ ! ’ ! ’ ! ’ MENU V-Position You can change the vertical position where the OSD menu appears on your monitor. MENU ! ’...
Adjusting the Monitor Transparency Change the transparency of the background of the OSD. • • MENU ! ’ ! ’ ! ’ ! ’ ! ’ ! ’ MENU Display Time The menu will be automatically turned off if no adjustments are made for a certain time period. You can set the amount of time the menu will wait before it is turned off.
Page 42
Adjusting the Monitor • 5 sec • 10 sec • 20 sec • 200 sec MENU ! ’ ! ’ ! ’ ! ’ ! ’ ! ’ MENU Setup Reset Reverts the product settings to factory defaults. • • MENU ! ’...
Adjusting the Monitor Customized Key You can specify a function which will be activated when the Customized Key ( )is pressed. MENU ! ’ ! ’ ! ’ ! ’ ! ’ ! ’ MENU Off Timer The monitors will turn off automatically at the specified time. •...
Adjusting the Monitor MENU ! ’ ! ’ ! ’ ! ’ ! ’ ! ’ ! ’ ! ’ MENU Image Size You can change the size of the screen displayed on your monitor. • Normal • Wide • Normal - The screen is displayed in accordance with the screen aspect ratio of the input signals.
Page 45
Adjusting the Monitor RTA (Response Time Accelerator) A function that accelerates the response speed of the panel so as to provide a sharper and more natural video display. • • Mode1 • Mode2 • Off - Deactivates the RTA function so that the panel operates at its original response speed. •...
Page 46
Adjusting the Monitor Information Shows a video source, display mode on the OSD screen. MENU ! ’ ! ’ MENU...
Troubleshooting Self-Test Feature Check Note Your monitor provides a self test feature that allows you to check whether your monitor is functioning properly. Self-Test Feature Check Turn off both your computer and the monitor. Unplug the video cable from the back of the computer. Turn on the monitor.
Troubleshooting noisy, and video mode not supported, etc. In this case, first check the source of the problem, and then contact the Service Center or your dealer. Judging the monitor's working condition If there is no image on the screen or a "Not Optimum Mode", "Recommended Mode 1680 x 1050 60 Hz"...
Page 49
Troubleshooting There is no image on the screen. Is the power indicator on the monitor blinking at 1 second intervals? The monitor is in PowerSaver mode. Press a key on the keyboard to activate the monitor and restore the image on the screen. If there is still no image, press the ' /SOURCE' button.
When you have a problem with the graphic card, visit our website to check the compatible graphic card list provided. http://www.samsung.com/monitor/magictune MagicTune™ doesn't work properly. Have you changed your PC or video graphic card? Download the latest program. The program can be downloaded http://www.samsung.com/mon- itor/magictune Did you install the program?
Troubleshooting Reboot the computer after installing the program for the first time. If a copy of the program is already installed, remove it, reboot the computer, and then install the program again. You need to reboot the computer for it to operate normally after installing or removing the program. Note Visit the MagicTune™...
Page 52
Troubleshooting Windows ME/2000: Set the resolution at the Control Panel ! ’ Display ! ’ Screen Saver. Set the function in the BIOS-SETUP of the computer. (Refer to the Windows / Computer Man- ual). How can I clean the outer case/LCD Panel? Disconnect the power cord and then clean the monitor with a soft cloth, using either a cleaning solution or plain water.
Specifications (2053NW)General General Model Name SyncMaster 2053NW LCD Panel Size 20 inch (51cm) Display area 433.44 mm (H) x 270.9 mm (V) Pixel Pitch 0.258 mm (H) x 0.258 mm (V) Synchronization Horizontal 30 ~ 81 kHz Vertical 56 ~ 75 Hz Display Color 16.7M...
Page 54
This monitor is EPA ENERGY STAR compliant and EN- ERGY2000 compliant when used with a computer equipped with VESA DPM functionality. ® As an ENERGY STAR Partner, SAMSUNG has determined ® that this product meets the ENERGY STAR guidelines for energy efficiency.
Page 55
Specifications (2053NW)Preset Timing Modes If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjusts the screen as follows. Display Mode Horizontal Vertical Fre-...
Page 56
Specifications LCD Panel Pixel Pitch 0.282 mm (H) x 0.282 mm (W) Synchronization Horizontal 30 ~ 81 kHz Vertical 56 ~ 75 Hz Display Color 16.7M Resolution Optimum resolution 1680 x 1050@60 Hz Maximum resolution 1680 x 1050@60 Hz Input Signal, Terminated RGB Analog 0.7 Vp-p ±...
Page 57
This monitor is EPA ENERGY STAR compliant and EN- ERGY2000 compliant when used with a computer equipped with VESA DPM functionality. ® As an ENERGY STAR Partner, SAMSUNG has determined ® that this product meets the ENERGY STAR guidelines for energy efficiency. (2253NW)Preset Timing Modes If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically.
Page 58
Specifications Display Mode Horizontal Vertical Fre- Pixel Clock Sync Polarity Frequency quency (Hz) (MHz) (H/V) (kHz) IBM, 640 x 480 31.469 59.940 25.175 IBM, 720 x 400 31.469 70.087 28.322 MAC, 640 x 480 35.000 66.667 30.240 MAC, 832 x 624 49.726 74.551 57.284...
Information For Better Display Adjust the computer resolution and screen injection rate (refresh rate) on the computer as described below to enjoy the best picture quality. You can have an uneven picture quality on screen if the best picture quality is not provided for TFT-LCD. •...
Page 60
Information when switching to a new video image. All display products, including LCD, are subject to image retention. This is not a product defect. Please follow the suggestions below to protect your LCD from image retention. Power Off, Screen Saver, or Power Save Mode •...
Page 61
Information • Every 30 minutes, change the characters with movement. The best way to protect your monitor from Image retention is to set your PC or System to operate a Screen Saver program when you are not using it. Image retention may not occur when a LCD panel is operated under normal conditions. Normal conditions are defined as continuously changing video patterns.
Page 62
Information Our LCD Monitor satisfies ISO13406-2 Pixel fault Class II...
Appendix Contact SAMSUNG WORLDWIDE Note If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center. North America U.S.A 1-800-SAMSUNG(726-7864) http://www.samsung.com/us CANADA 1-800-SAMSUNG(726-7864) http://www.samsung.com/ca MEXICO 01-800-SAMSUNG(726-7864) http://www.samsung.com/mx Latin America ARGENTINE 0800-333-3733 http://www.samsung.com/ar BRAZIL 0800-124-421 http://www.samsung.com/br...
Page 65
Appendix Middle East & Africa SOUTH AFRICA 0860-SAMSUNG(726-7864) http://www.samsung.com/za TURKEY 444 77 11 http://www.samsung.com.tr U.A.E 800-SAMSUNG(726-7864) http://www.samsung.com/mea 8000-4726 Terms Dot Pitch The image on a monitor is composed of red, green and blue dots. The closer the dots, the higher the resolution. The distance be- tween two dots of the same color is called the 'Dot Pitch'.
Reproduction in any manner whatsoever without the written permission of Samsung Electronics Co., Ltd. is strictly forbidden. Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for incidental or con- sequential damages in connection with the furnishing, performance, or use of this material.