Panasonic NV-MX1B Operating Instructions Manual page 50

Indications
1 4
r
SP 0:00.00
2
R0:45
10 k W
ª51MF
CINEMA
3
D.ZOOM
NEGA
1
Remaining Battery Power
As the remaining battery power decreases, the
indication changes as follows:
r # s # t # u # v
When the Battery is completely discharged, the
u (v) Indication flashes.
(When you are using the AC Adaptor, the
s Indication may appear, however, this
has no meaning in this case.)
2
Remaining Tape Time
The remaining tape time is displayed in
minutes. (When it becomes less than
3 minutes, the indication starts to flash.)
≥If a recording lasts less than 15 seconds, the
remaining tape time cannot be displayed
correctly.
≥The displayed remaining tape time may be
shorter than the actual remaining tape time.
3
Cinema Mode (p. 36)
When recording in the Cinema Mode, this
indication is displayed.
Digital Zoom (p. 32)
When the Digital Zoom Function is activated,
this indication is displayed.
Digital Effects (p. 52, 66)
When a digital effect is activated, the
corresponding indication is displayed.
Playback Zoom (p. 76)
When the Playback Zoom Function is activated,
this indication and the zoom magnification are
displayed.
4
Recording Speed Mode (p. 13)
The selected Recording Speed Mode is
displayed.
SP: Standard Mode
LP: Long-play Mode
98
r
REC 0:00.00
SP
5
T
R0:45
MNL
6
5
Zoom Magnification (p. 32)
When you push the [W/T] Zoom Lever up or
down, the Zoom Magnification Indication and
the Zoom Gauge are displayed.
Recording Mode (p. 26, 30, 50, 62, 64)
AUTO: This appears when the Mode
Selector Switch is set to [AUTO].
MNL: This appears when the Mode
Selector Switch is set to [MNL].
Super Image Stabilizer (p. 36)
[: When the Super Image
Stabilizer Function is activated,
this indication is displayed.
Audio Dubbing Input Display (p. 78)
(NV-MX7 only)
MIC/AV IN: The Audio Dubbing Input Mode
indication is displayed.
Audio Recording Mode (p. 78)
12bit/16bit: The indication of the Audio
Recording Mode that was
selected for recording is
displayed during playback.
Automatic Printing (p. 112)
AUTOPRINT: This indication is displayed when
the Autoprint Function is being
used.
6
Manual Focus (p. 30)
If you select the Manual Focus Mode, the [MF]
Indication is displayed.
Back Light Mode [ª] (p. 28)
When the Backlight Compensation Function is
active, this indication is displayed.
Programme AE Mode (p. 50)
The Programme AE Function offers the
following settings:
5: Sports Mode
7: Portrait Mode
4: Low Light Mode
Ω:
Spotlight Mode
º: Surf & Snow Mode
1
7 r SP
R0:45
CINEMA
D.ZOOM
NEGA
REC
{
8
1/500
9
1F2.4
4
r SP
R0:45
CINEMA
D.ZOOM
NEGA
7
Tape Run Indications
REC: Recording (p. 26)
PAUSE: Recording Pause (p. 26)
Playback (p. 38)/Camera Search in
!:
forward direction (p. 44)
Camera Search in reverse direction
":
(p. 44)
Still Playback (p. 40)
;:
Fast-forward/Cue Playback (p. 38)
%:
Rewind/Review Playback (p. 38)
&:
: Slow Playback in forward direction/
}/~
Slow Playback in reverse direction
(p. 40)
;!/";: Still Advance Playback in forward
direction/Still Advance Playback in
reverse direction (p. 40)
)/ *: Index Search in forward direction/
Index Search in reverse direction
(p. 46)
CHK: Recording Check (p. 28)
A.DUB!: Audio Dubbing (p. 78)
A.DUB;: Audio Dubbing Pause (p. 78)
PHOTO: Recording in the Photoshot Mode
(p. 34)
BLANK: Blank Search (p. 44)
2k%: Variable Speed Search (p. 39)
R !: Repeat Playback (p. 39)
≥When you record with the LCD Monitor facing
forward using the Mirror Mode, none of the Tape
Run Indications shown above appear. Only the
Remaining Battery Power Indication, the
Recording Indication [¥], the Recording Pause
Indication [¥;] and Card Photoshot Indication
[ø] (NV-MX5, NV-MX7 only) appear. If the [°]
Indication appears, turn the LCD Monitor so that
it faces backward and then confirm the displayed
warning message(s).
:
2
0:00.00
r SP M 0:00.00
REC
REC
AUTO R0:45
AUTO
CINEMA
D.ZOOM
NEGA
5
0:00.00
REC REC
MNL
1AWB
1AWB
8
Shutter Speed (p. 64)
When you manually adjust the shutter speed,
this indication is displayed.
9
Iris Value (F Number) (p. 64)
When you manually adjust the iris, this
indication is displayed.
:
Tape Counter, Time Code (p. 121)
The Tape Counter, Memory Stop Function or
Time Code Indication is displayed.
Changing the Counter Display Mode
By changing the setting for [C.DISPLAY] on the
[DISPLAY SETUP] Sub-Menu, the Counter
Display Mode can be changed in the order shown
in the above illustrations
1
COUNTER:
2
MEMORY:
3
TIMECODE: Time Code Indication
Changing the Display Mode
By changing the setting for [DISPLAY] on the
[DISPLAY SETUP] Sub-Menu, the Counter
Display Mode can be changed in the order shown
in the above illustrations
4
ALL:
5
PARTIAL:
6
OFF:
3
r
SP 0h 00m 00s 00f
REC
R0:45
AUTO
CINEMA
D.ZOOM
NEGA
6
REC
1 3
– .
Tape Counter Indication
Tape Counter Indication with
activated Memory Stop Indication
4 6
– .
All indications appear (initial
setting)
Only a few indications appear
The minimally required
indications, such as the
Operation Mode Indications and
Warning/Alarm Indications,
appear
99