Table of Contents
Advertisement
R e a d o u t s
The MAC 300 has counters to track usage, maintenance intervals, lamp life, etc. One set of counters shows total
(
TOT L
) accumulated usage and cannot be reset. Another set shows usage since the counter was reset (
reset one of these counters, navigate to the readout and press [ ] for 5 seconds.
H o u r s u s e d
To read the accumulated total number of hours the fixture has been on, navigate to
[Enter]. To read the number of hours since the counter was last reset, navigate to
[Enter]. To reset this counter, navigate to the readout and press [ ] for 5 seconds.
L a m p h o u r s
To read the accumulated total number of lamp hours, navigate to
the number of lamp hours since the counter was last reset, navigate to
reset this counter when installing a new lamp, navigate to the readout and press [ ] for 5 seconds.
L a m p s t r i k e s
To read the accumulated total number of lamp strikes, navigate to
the number of lamp strikes since the counter was last reset, navigate to
reset this counter when installing a new lamp, navigate to the readout and press [ ] for 5 seconds.
S o f t w a r e v e r s i o n
Navigate to the sub menu under
cuit software (
U t i l i t i e s
U p l o a d m o d e
The software upload mode is engaged automatically by the MPBB1 Uploader. Engage upload mode manually only if
automatic upload fails. To do so, navigate to
displayed to confirm, or press [Menu] to escape. See also "Updating software" on page 19.
D e m o n s t r a t i o n p r o g r a m
The demonstration menu allows you to run a preprogrammed stand-alone program. Before running the demo, set the
minimum and maximum pan and tilt positions (
effects. Select
Te s t p r o g r a m s
Te s t s e q u e n c e
Navigate to
TE ST
to stop the program.
D M X l o g
The DMX log provides a quick way to check if the fixture is receiving DMX instructions correctly. The log displays
the start code (
To read a value, navigate to
the DMX value received. Look up the value's function in the DMX protocol to see if it corresponds to the effect's
behavior.
Q u a l i t y c o n t r o l a n d s e r v i c e t e s t s
The
PCB
and
TES T
FA CT
(
/
INF O
/
VE R
F EBA
), and display module software (
GO
and press [Enter] to run the demo. Press [Menu] to stop the program.
/
TS EQ
and press [Enter] when
STC O
), which must be 0, and the DMX values received on each control channel.
TES T
DMX L
/
F ACT
menus, under
TES T
ETS T
/
) drives all effects at 10 percent over their maximum speed.
IN FO
IN FO
INF O
IN FO
to read the version number of the CPU software (
dIS P
).
U TIL
U PLd
/
and press [Enter]. Press [Enter] again when
M INP
MAXP
MIN T
,
,
RU N
is displayed to perform a general fixture test. Press [Menu]
and press [Enter]. Scroll to an effect channel and press [Enter] to read
, contain tests for factory and service use. The factory effects test
Fixture Settings
INF O
/
H RS
/
T OTL
INF O
/
HRS
/
RS ET
/
L H R
/
TO TL
and press [Enter]. To read
/
L HR
/
R SET
and press [Enter]. To
/
L ST
/
TOT L
and press [Enter]. To read
/
L ST
/
RSET
and press [Enter]. To
C PU
MAX T
,
) to a good location for viewing the
RS ET
). To
and press
and press
), feedback cir-
S URE
is
13
Hide quick links:
Advertisement
Table of Contents
