Auto Setup Function - Panasonic NV-HS820 Series Operating Instructions Manual

If you are connecting your VCR to a TV using RF coaxial
cable and 21-pin Scart cable, then follow the steps.
(AV Connection)
RF Coaxial cable must be connected to watch TV channels
even if 21-pin Scart cable is used to connect VCR to TV.
1 2 3
4
11
1 AV1 21-pin Scart socket
2 Normal/S-Video Output switch
3 Aerial Input socket
4 Aerial Output socket
5 Aerial (not supplied)
6 Aerial lead (not supplied)
Hint:
– If the TV set is equipped with a 21-pin Scart socket that
features Y/C signal separation, set the [Normal/S-Video
Output] switch on the rear panel to [S-VIDEO OUT] so that
you can play back with high picture quality and use a
fully-wired 21-pin Scart cable (not supplied) to connect the
VCR to the TV.
If you are connecting your VCR to a TV using S-Video cable,
then follow the steps. (S-Video Connection)
RF Coaxial cable must be connected to watch TV channels.
1 3
2 4
1 S-Video Output socket
2 Audio Output socket
3 Aerial Input socket
4 Aerial Output socket
5 Aerial (not supplied)
6 Aerial lead (not supplied)
7 TV with S-Video Input socket
(not supplied)
5
6
7
8
10
9
07 TV (not supplied)
08 Aerial Input socket
09 21-pin Scart socket
10 RF Coaxial cable (supplied)
11 Fully-wired 21-pin Scart cable
(not supplied)
5
6
7
9
8
13
12
10
11
08 Aerial Input socket
09 S-Video Input socket
10 Audio Input socket
11 Audio cables (not supplied)
12 S-Video cable (not supplied)
13 RF Coaxial cable (supplied)

Auto Setup Function

The Auto Setup function automatically tunes all available TV
stations and sets the VCR's clock to the current date and
time.
Press the [VCR-ON/OFF] button
Í
to turn on the VCR.
The Country setting menu
appears on the TV screen.
Press the [Cursor] buttons 3421.
Select the country where you are using the VCR.
Press the [OK] button.
OK
The VCR's Auto Setup
automatically starts and tunes all
available TV stations and also
sets the clock. This takes about
5 minutes.
When the indication appears on
the VCR display, the Auto Setup
is complete.
Press the [MENU] button for more than 5 seconds.
MENU
The RF output channel number appears on the VCR
display.
The initial setting is channel 36.
Press the [Numeric] button [0].
The displayed RF output channel number changes to
[– –].
Press the [OK] button to conclude the setting.
OK
To cancel the Auto Setup before it has finished
Press the [EXIT] button .
EXIT
When the clock setting menu appears after Auto Setup
has finished
Press the [Cursor] buttons 3421 to set the correct
time and date.
Press the [OK] button to conclude the setting.
OK
To confirm that the TV stations have been tuned correctly
by the Auto Setup function
See page 18.
When no station has been set, confirm all connections of
the VCR again and restart the Auto Setup
See page 19.
When the station names and/or channel numbers have
not been set correctly
See page 18.
Hint:
– If you select [Schweiz], [Suisse] or [Svizzera] on the
Country setting menu, the other setting menu appears
automatically to let you set [Power save] to [ON]. In this
setting, the VCR's power consumption is minimised when it
is off (Standby mode). To turn the VCR on, keep the [VCR-
ON/OFF] button pressed on the VCR main unit, not with the
remote control.
Panasonic VCR
Country
Belgien Deutschland
Österreich
Belgique
Portugal
België
Danmark Suomi
España Sverige
Schweiz
Ελλάδα
Suisse
France
Italia Svizzera
Nederland others
Norge
Panasonic VCR
Auto-Setup
: others
Country
: Ch 21
Tuning
7