Timer Recording - Panasonic NV-HS820 Series Operating Instructions Manual

Timer Recording

This VCR lets you programme up to 16 TV programmes
(including weekly and daily programmes) for unattended
recording up to one month in advance.
To Programme with the On Screen Display
(OSD)
This method offers easy step-by-step programming with the
remote control while you view the prompts on the TV screen.
Example:
Programming the timer recording of a TV programme
broadcast on programme position 2 (ZDF) from 20:00 to
21:30 on 27 October.
Press the [PROG./CHECK]
PROG. / CHECK
button to display the menu for
programming timer recordings
on the TV screen.
– Alternatively, you can press the [MENU] button and
then select [Timer recording].
Press the [Channel] button to select the programme
position of the desired TV station.
– As an alternative method, after pressing the [Channel]
button, you can use the [Cursor] buttons 3421.
Press the [DATE] button to set the date on which the TV
r
programme will be broadcast.
DATE
s
Press the [ON] button to set the starting time.
r
– When it is kept pressed, the indication changes
ON
in 30-minute intervals.
s
Press the [OFF] button to set the ending time.
r
OFF
s
Press the [SP/LP/EP] button to set the desired tape
SP/LP/EP
speed.
– Regarding the [A] indication, refer to page 15.
Press the [Cursor] buttons 3421 to set [VPS/PDC] to
[ON] or [OFF] [jjj].
– See page 15 for VPS/PDC recording.
Press the [OK] button to
OK
conclude the setting.
Press the [TIMER] button to switch the VCR over to the
TIMER
Á
timer recording standby mode.
– Check that [Á] is lit on the VCR display.
If it is flashing, check the timer recording details
again. (See page 15.)
14
To Programme with the ShowView
Function
The ShowView numbers make it extremely easy to set the
VCR for timer recording.
The duration of a timer recording programmed with
ShowView number may be slightly longer than the actual
duration of the TV programme.
S
Corporation. The S
under licence from Gemstar Development Corporation.
Example:
Programming a timer recording of a TV programme with the
ShowView number 721114
SV/V +
Panasonic VCR
Timer recording
1/2
Pos Start Stop VPS
1
Name DATE ON OFF PDC
1. : :
jjjjj jj/jj jj jj jj jj jj jjj
2. : :
jjjjj jj/jj jj jj jj jj jj jjj
3. : :
jjjjj jj/jj jj jj jj jj jj jjj
4. : :
jjjjj jj/jj jj jj jj jj jj jjj
5
jjjjj jj jj jj jj jj jj jj jjj
jjjjj jj jj jj jj jj jj jj jjj
jjjjj jj jj jj jj jj jj jj jjj
jjjjj jj jj jj jj jj jj jj jjj
SP/LP/EP
TIMER
To Suspend the Timer Recording Standby
Mode
Press the [TIMER] button so that the [Á] indication on the
VCR display disappears.
After you have finished using the VCR, be sure to reactivate
the timer recording standby mode by pressing the [TIMER]
Panasonic VCR button again, otherwise the programmed timer recording will
Timer recording
1/2
Pos Start Stop VPS
not be performed.
1
Name DATE ON OFF PDC
1. ZDF 27/10 20:00 21:30 SP ON
2. : :
jjjjj jj/jj jj jj jj jj jj jjj
3. : :
jjjjj jj/jj jj jj jj jj jj jjj
4. : :
jjjjj jj/jj jj jj jj jj jj jjj
Note:
jjjjj jj jj jj jj jj jj jj jjj
jjjjj jj jj jj jj jj jj jj jjj
jjjjj jj jj jj jj jj jj jj jjj
– If the VCR is not put in the timer recording standby mode at
jjjjj jj jj jj jj jj jj jj jjj
V is a trademark of Gemstar Development
HOW IEW
V
HOW IEW
+
Press the [SV/V ] button to
display the menu for entering
the ShowView number on the
TV.
Press the [Numeric] buttons to enter the ShowView
number.
– If you have entered a wrong digit, press the [Cursor]
button 2 and then enter the correct digit.
Press the [OK] button to display the programmed
OK
content.
Press the [SP/LP/EP] button to set the desired tape
speed.
– Regarding the [A] indication, refer to page 15.
– To change timer recording programmings, use the
[Cursor] buttons 3421, the [Channel], [DATE],
[ON] or [OFF] button.
– See page 15 for VPS/PDC recording.
Press the [OK] button again to conclude the settings.
OK
Press the [TIMER] button to switch the VCR over to the
Á
timer recording standby mode.
– Check that [Á] is lit on the VCR display.
If it is flashing, check the timer recording details
again. (See page 15.)
the latest 10 minutes before the programmed timer
recording starting time, the [Á] flashes on the VCR display.
In this case, press the [TIMER] button to put the VCR in the
timer recording standby mode.
system is manufactured
Panasonic VCR
ShowView
7 2 1 1 1 4