Panasonic NV-GS80EB Operating Instructions Manual page 43

LSQT1131_ENG.book 43 ページ ２００７年１月１１日 木曜日 午前９時５分
4: Auto focus function does not work.
• Is manual focus mode selected? If auto focus
mode is selected, focus is automatically
adjusted.
• There are some recording subjects and
surroundings for which the auto focus does not
operate correctly. ( ) If so, use the manual
-48-
focus mode to adjust the focus. (
Indications
1: A sentence is displayed in red in the screen
centre.
• Read the contents and respond to them. (
2: The remaining tape time indication
disappears.
• The remaining tape time indication may
disappear temporarily during frame-by-frame
playback or other operation. If you continue
ordinary recording or playback, the indication is
restored.
3: The remaining tape time Indication does not
match the actual remaining tape time.
• If scenes of less than 15 seconds are
continuously recorded, the remaining tape time
cannot be correctly displayed.
• In some cases, the remaining tape time
indication may show remaining tape time that is
2 to 3 minutes shorter than the actual
remaining tape time.
4: A function indication such as mode
indication, remaining tape time indication,
or time code indication is not shown.
• If you set [SETUP] >> [DISPLAY] >> [OFF],
indications other than the tape running
condition, warning, and date indications
disappear.
Playback (Sound)
1: Sound is not played back from the built-in
speaker of the movie camera.
0 Is the volume too low? During playback, push
the [sVOLr] lever to display the volume
indication and adjust it. (
2: Different sounds are reproduced at the
same time.
• Have you set [SETUP] >> [AUDIO OUT] >>
[STEREO] and reproduced a picture containing
the main sound and sub sound? Set to [L] to
hear main sound, and set to [R] to hear the sub
sound. ( )
-38-
Others
Playback (Pictures)
1: Mosaic-pattern noise appears on images
• This phenomenon is characteristic of digital
2: Horizontal stripes appear on images during
) • Horizontal stripes may appear depending on
-29-
3: Although the movie camera is correctly
)
-40-
• Have you selected video input on the TV?
• Is the [TV ASPECT] setting correct? Change
4: Playback picture is not clear.
• Are the heads of the movie camera dirty? If the
• If the terminal for the AV cable is soiled, noises
• Is a picture containing a copyright protection
Others
1: The indication disappears, the screen is
• Turn off the power to the movie camera. If the
)
-31-
during cue or review playback.
video systems. It is not a malfunction.
cue and review playback.
the scene, but this is not a malfunction.
connected to a TV, playback images cannot
be seen.
The images are vertical.
Please read the operating instructions of your
TV and select the channel that matches the
input terminals used for the connection.
the setting to match the aspect ratio of the TV.
[SETUP] >> [TV ASPECT] >> [16:9] or [4:3].
heads are dirty, playback image cannot be
clear. Clean the heads by using the head
cleaner for digital video (optional). (
may appear on the screen. Wipe the soil off the
terminal with a soft cloth, and then connect the
cable to the A/V terminal.
signal (copy guard) being recorded? When a
protected picture is played back by the movie
camera, mosaic-like patterns appear on the
picture.
frozen, or no operation can be performed.
power cannot be turned off, press the [RESET]
button, or detach the battery or the AC adaptor
and then reattach it. After that, turn on the
power again. If normal operation is still not
restored, detach the power connected, and
consult the dealer who you purchased the
movie camera from.
)
-45-
43
LSQT1131