Still Pictures - Panasonic Diga DMR-EX93C Operating Instructions Manual

Troubleshooting guide
Music
Tracks could not be copied to the HDD.
If there are copyright protected tracks such as SCMS
restrictions, they will not be copied.
Recording from CDs that do not conform to CD-DA
specifications (copy control CDs, etc.) cannot be guaranteed.
Bonus tracks may not be copied.
ID3 tag of a MP3 file or WMA tag of a WMA file is
not completely displayed.
Only the track name ([HDD] [USB]) and artist name ([HDD]) can
be displayed with this unit.

Still pictures

Cannot display DIRECT NAVIGATOR screen.
This screen cannot be displayed during recording or copy or
while the unit is standing by for linked timer recording with
external equipment.
Cannot edit or format a card.
Release the card's protection setting. (With some cards, the
"Write Protection Off" message sometimes appears on the
screen even when protection has been set.) (
The contents of the card cannot be read.
Remove the card from the slot and then insert again. If this
does not solve the problem, turn off and turn on the unit again.
The card format is not compatible with the unit. (The contents
on the card may be damaged.)
This unit is compatible with SD Memory Cards that meet SD
Card Specifications FAT12 and FAT16 formats, as well as
SDHC Memory Cards in FAT32 format. (
The card contains a folder structure and/or file extensions that
are not compatible with this unit. (
You can use SD Memory Cards with capacities from 8 MB to 2 GB
and SDHC Memory Cards with capacities from 4 GB to 32 GB.
This unit cannot play AVCHD format motion pictures or MPEG4
on an SD card.
Copying, deleting and setting protection takes a
long time.
When there are a lot of folders and files, it may sometimes take
a few hours.
When repeating copying or deleting, it may sometimes take a
long time. Format the disc or card. (
Still pictures (JPEG) do not playback normally.
The images that were edited on the PC, such as
PROGRESSIVE JPEG etc., may not playback. (
USB
The contents of the USB memory cannot be read.
Remove the USB memory from the USB port and then insert
again. If this does not solve the problem, turn off and turn on the
unit again.
Check that the USB memory is inserted correctly. (
The format of the USB memory or of its contents is not
compatible with the unit. (The contents on the USB memory
may be damaged.) (
The USB memory contains a folder structure and/or file
extensions that are not compatible with this unit. (
Turn off and then turn on the unit again.
USB memories connected using a USB extension cable or a
USB hub may not be recognized by this unit.
Some USB memories cannot be used with this unit. (
If inserted during playback, recording or copying etc., the USB
memory may not be recognized by this unit.
VQT2J40
86
65)
15)
15, 16)
65)
16)
17)
15, 16)
16)
TV Guide
The TV Guide System does not receive any data.
This unit can only display either the TV Guide for the digital
broadcasts or for the analogue broadcasts. Default setting is TV
Guide for the digital broadcasts. To display the TV Guide for the
analogue broadcasts, change "TV Guide Type" in Setup menu.
( 74)
[Analogue] The GUIDE Plus+ system data is updated several
times each day. When the unit is first connected, the GUIDE
Plus+ system is not yet ready to receive data.
It takes approximately 2 hours to complete data download.
Depending on when you set up this unit, it may take
approximately one day before you can display the television
programme list. (
[DVB-T] [Analogue] In the area where GUIDE Plus+ system is
available, check whether correct post code is entered. (
74)
Check whether TV Guide system setup was performed in full.
Check whether the clock is properly set. (
If signal quality is bad (ghost images or limited reception), the
TV Guide system may not be able to receive any data.
"No Data" is displayed for some or all stations.
[Analogue] These stations may not have been able to be
identified automatically.
For these stations, select the "On" in the sub menu under
"Editor" and assign the correct reference station manually.
( 33)
Some stations are not supported by the TV Guide system.
Programme the Timer recording manually or via S
( 29, 32)
The TV Guide information is not displayed
properly.
[Analogue] The reference station is not assigned correctly in
"Editor".
Select the correct reference station. (
[Analogue] Programme information about analogue broadcasts
is not displayed when you set "TV Guide Type" to "Digital
Channels".
To use the TV Guide for the analogue broadcasts, change "TV
Guide Type". (
There was a programme change.
Check the current programme, e.g. on the Web site for the TV
Guide system provider or station provider.
The TV Guide data transfer was interrupted.
The TV Guide system shows the data that was received up to
the interruption.
The programme information may be incomplete.
The TV Guide data is not updated.
The unit must be in standby mode in order to update the data. If
the unit is in EXT LINK mode (EXT-L lights up in the display),
then the data update may also not work.
Make sure that the time is set correctly.
[DVB-T] [Analogue] Make sure that "TV Guide Download in
Standby" or "Night Download" is set to "On". (
15)
12, 33)
73)
33)
74)
33, 74)
33,
V .
HOW IEW