1. Manuals
  2. Brands
  3. Panasonic Manuals
  4. Monitor
  5. WVBM500 - B&W MONITOR
  6. Operating instruction

Panasonic WV-BM500 Operating Instruction

Video monitor
Hide thumbs Also See for WV-BM500:
Table of Contents

Advertisement

Quick Links

Download this manual

Video Monitor

WV-BM500
Before attempting to connect or operate this product,
please read these instructions completely.

Advertisement

Table of Contents
loading

Related Manuals for Panasonic WV-BM500

Summary of Contents for Panasonic WV-BM500

  • Page 1: Video Monitor

    Video Monitor WV-BM500 Before attempting to connect or operate this product, please read these instructions completely.
  • Page 2 If you lose the fuse cover the plug must not be used until a replacement SHOCK, DO NOT REMOVE COVER (OR cover is obtained. BACK), NO USER SERVICEABLE PARTS A replacement fuse cover can be purchased from your local Panasonic Dealer. INSIDE. REFER SERVICING TO QUALIFIED SERVICE IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE SOCKET PERSONNEL.
  • Page 3 L or coloured red. encias de radio 87/308/EEC). How to replace the fuse Open the fuse compartment with La Società PANASONIC ITALIA S.p.A., importatrice di a screwdriver and replace the fuse questo prodotto, dichiara che questo apprarecchio è and fuse cover.

  • Page 4: Table Of Contents

    CONTENTS PREFACE ..................................2 FEATURES ..................................2 PRECAUTIONS ................................2 MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS ..................3 OPERATING PROCEDURE ............................5 INSTALLATION ................................6 CONNECTIONS ................................7 SYSTEM CONNECTIONS .............................. 8 SPECIFICATIONS ................................9 STANDARD ACCESSORIES ............................10 The model numbers listed in this Operating Instructions have no suffixed attached to it.

  • Page 5: Preface

    • Do not block the ventilation slots on the rear panel and side cover. • When mounting the Model WV-BM500 in an EIA standard 19” rack, be careful to insure that the interior temperature of the rack does not exceed...

  • Page 6: Major Operating Controls And Their Functions

    MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS <Front View> <Rear View> HEIGHT V.LIN FOCUS H.HOLD V.HOLD BRIGHT CONTRAST POWER Video Monitor WV-BM !1 !2 !3 !4 !5 1. Power On/Off Switch (POWER, ON/OFF) Press again, the switch comes up (l) for turning This is a push-push type switch which turns the off the power of the monitor.
  • Page 7 3. Horizontal Hold Control [H-HOLD] This control is used to Lock in the picture horizon- 10. DC Restoration Switch [DC REST] tally. Switch to restore background of picture. 4. Height Control [HEIGHT] 11. Video Input Connector (VIDEO IN) Adjust the vertical height of the picture. This connector accepts the input video signal 5.

  • Page 8: Operating Procedure

    OPERATING PROCEDURE 5. Height (4) This recessed screwdriver control should be adjusted simultaneously to give proper vertical 1. Set the Power On/Off Switch (1) to the ON (;) height consistent with good vertical linearity. position. Adjustment should be made to extend the picture limits approximately 1/10”...

  • Page 9: Installation

    The following installation should be made by qualified service personnel or system installers. Mounting into EIA Standard 19” Rack Model WV-BM500 can be mounted into EIA 19” rack as shown below. Note: Rack Mounting requires the purchase of optional WV-Q64 Rack Angle Bracket.

  • Page 10: Connections

    CONNECTIONS External Sync When a non-composite video signal is connected to Power Cable the monitor, it will be necessary to connect an external 1. Keep the camera Power switched OFF during composite sync signal to the monitor. installation. 1. Connect the Sync Input Connector (14) on the 2.

  • Page 11: System Connections

    Internal Sync Connection • Connect the Video Input Connector (11) on the monitor to the Video Out Terminal of cameras with 1. Single Monitor Connection WV-BM500 75-ohm coaxial cables. Camera External Sync Connection • When a non-composite video signal is connected 220-240V Coax.

  • Page 12: Specifications

    SPECIFICATIONS Power Source : WV-BM500/A, WV-BM500/B, WV-BM500/G: 220-240V AC50Hz Power Consumption : Approx. 14W Tube Size : 5” diagonal actual visual size Video Input Impedance : 75Ω or high impedance (Auto Termination) Video Input Level : 1.0 Vp-p composite (0.5 Vp-p - 2.0 Vp-p)

  • Page 13: Standard Accessories

    OPTIONAL ACCESSORY Rack Angle Bracket ......... WV-Q64 -10-...
  • Page 14 Matsushita Electric Industrial Co., Ltd. Central P.O. Box 288, Osaka 530-91, Japan N0194-0 YWV8QA3285AN Printed in Japan N 13 Gedruckt in Japan Imprimé au Japon...

Table of Contents