Panasonic Viera TX-P50VT50B Operating Instructions Manual page 118

Problem
Sound is unusual
Pictures from external
equipment are unusual
when the equipment is
connected via HDMI
Cannot connect to the
network
Cannot select the file
during DLNA operations
Cannot operate
VIERA Connect
The TV does not switch on
The TV goes into Standby
mode
The remote control does
not work or is intermittent
The touch pad controller
does not work or is failed
to register
Parts of the TV become
hot
Permanently lit spots on
screen
Overcurrent error
message appears
An error message appears
118
●
Set the sound setting of the connected equipment to "2ch L.PCM".
●
Check the [HDMI1 / 2 / 3 / 4 Input] setting in the Sound Menu.
● If digital sound connection has a problem, select analogue sound connection.
(p. 111)
●
Check the HDMI cable is connected properly.
● Turn the TV and equipment off, then turn them on again.
●
Check an input signal from the equipment.
●
Use equipment compliant with EIA/CEA-861/861D.
●
Check the LAN cable or wireless LAN is connected properly.
●
Check the connections and settings.
●
Check the network equipment and network environment.
● The router may not be set to issue IP address automatically. If the network
administrator prefers to allocate an IP address, set an IP address manually.
(p. 91)
●
The router may be using MAC address filtering (security setting).
Confirm the MAC Address of this TV (p. 48) and set the router to use it.
● If the problem persists, consult your Internet Service Provider or
telecommunications company.
● Is media server of the connected equipment prepared?
● Check applicable data format.
●
Check the settings of [Network Link Settings]
● Check the connections and settings.
●
The server or connected line may be busy now.
● Press and hold the Standby On / Off switch on the remote control for about
1 second if Power LED is red.
●
Check the mains lead is plugged into the TV and the socket outlet.
●
The fuse in the mains plug may have blown. Replace it with one of an identical
rating. (p. 4)
●
Auto power standby function is activated.
●
The TV enters Standby mode about 30 minutes after analogue broadcasting
ends.
●
Are the batteries installed correctly?
●
Has the TV been switched on?
● The batteries may be running low. Replace them.
●
Point the remote control directly at the TV's remote control signal receiver
(within about 7 m and a 30 degree angle of the signal receiver).
●
Situate the TV away from sunshine or other sources of bright light not to shine
on the TV's remote control signal receiver.
●
Are the batteries installed correctly?
●
The batteries may be running low. Replace them.
● Register again. [Pairing] in [VIERA Touch Pad Controller] (p. 49)
●
Use the touch pad controller within about 3.2 m from the TV. (The range may
be shortened depending on the obstacles between the TV and the controller, or
the surrounding environment.)
●
Even when the temperature of parts of the front, top and rear panels has risen,
these temperature rises do not cause any problems in terms of performance or
quality.
●
Due to production process involved in this technology this may result in some
pixels which are permanently lit or unlit. This is not a malfunction.
●
The connected USB device might cause this error. Remove the device and turn
the TV off with Mains power On / Off switch, then turn it on again.
●
Check foreign objects are not inside the USB port.
●
Follow the message's instructions.
●
If the problem persists, contact your local Panasonic dealer or the authorised
service centre.
Causes / Actions
(p. 106)
(p. 113)
(p. 90 - 93)
(p. 108, 109)
(p. 90)
(p. 90 - 93)
(p. 13)
(p. 8)
(p. 8)
(p. 48)
(p. 90)
(p. 88)