Selecting A Surround Mode; On Off; Stand-By - Onkyo TX-SV353 Instruction Manual

Selecting a Surround mode

Surround system
Since the TX-SV353 is equipped with a front amplifier, center amplifier, and a rear (surround) amplifier, all Dolby Pro Logic Surround
effects can be produced. When using video cassette tapes or video discs that have the DOLBY STEREO or DOLBY SURROUND trade
mark, you can enjoy the feeling of a movie theater in your own room. When reproducing these effects, placement of the rear (surround)
speakers is important for optimum sound quality in your room.
For best results with Dolby Pro Logic Surround, use the test tone to adjust the volume of all speakers to the same level.
SYSTEM
DOLBY SURROUND
P R O • L O G I C
ON OFF
SPEAKERS A

STAND-BY

SPEAKERS B
SURROUND
MODE
PHONES
VIDEO / 1 VDP
1
1
SURROUND
MODE
2
CENTER
MODE
INPUT SELECTOR MULTI-CH
TV/AUX VIDEO-1 VIDEO-2 INPUT
3
TAPE TUNER PHONO C D
PROGRAMMABLE AREA TV/VIDEO
POWER C H
POWER
DECK-A DECK-B TUNER
GROUP
PRESET
C D SUR
DISC MODE MUTING
TEST
TONE
CH SEL
VOLUME
LEVEL
6
16
1 2 3
4 5 6
7 8 9
GROUP 0/10 SCAN
DOWN TUNING UP DIRECT TUNING
CENTER
MODE DELAY TIME MEMORY FM MUTE / MODE
CLEAR
BASS
VIDEO / 2 VCR TV/AUX TAPE(MONITOR) FM AM PHONO C D
AUDIO VIDEO CONTROL RECEIVER
2 6
POWER
DISC
DECK-A DECK-B TUNER
GROUP
4
PRESET
C D SUR
DISC MUTING
MODE
TEST
TONE
CH SEL
VOLUME
LEVEL
REMOTE CONTROLLER RC-383M
DELAY TIME
MASTER VOLUME
MIN MAX
TREBLE BALANCE
L R
TX-SV 353
DECK-A DECK-B TUNER
GROUP
PRESET
C D SUR
MUTING
MODE
TEST
TONE
CH SEL
VOLUME
LEVEL
INPUT SELECTOR MULTI-CH
TV/AUX VIDEO-1 VIDEO-2 INPUT
5
TAPE TUNER PHONO C D
PROGRAMMABLE AREA TV/VIDEO
POWER C H
POWER
DECK-A DECK-B TUNER
GROUP
PRESET
C D SUR
DISC MODE MUTING
TEST
TONE
CH SEL
VOLUME
LEVEL
SENDING/
LEARNED SEND LEARN
POWER SLEEP
INPUT SELECTOR MULTI-CH
TV/AUX VIDEO-1 VIDEO-2 INPUT
TAPE TUNER PHONO C D
PROGRAMMABLE AREA TV/VIDEO
POWER C H
POWER
DECK-A DECK-B TUNER
GROUP
PRESET
C D SUR
DISC MODE MUTING
3, 5
TEST
TONE
CH SEL
4
VOLUME
LEVEL
REMOTE CONTROLLER RC-383M
Adjusting the speaker
volumes before enjoying
Dolby Pro Logic Surround
Before operating: Be sure to turn on
SPEAKERS A and turn off SPEAKERS
B when listening to Dolby Pro Logic Sur-
round.
1. Select a source encoded with Dolby
Surround and use the SURROUND
MODE button to select DOLBY PRO
LOGIC mode.
2. Use the CENTER MODE button to
select a center mode.
When the button is pressed, the mode
will change as shown below.
NORMAL WIDEBAND
(Refer to page 17 for details of these
modes.)
3. Press the TEST TONE button on the
remote controller.
(Refer to Test Tone on page 17 for
details.)
4. From your listening position, use the
remote controller to adjust the rela-
tive volume level of the test tone from
the different speakers.
Adjust the volume levels of all of the
speakers with the VOLUME π (up)
and † (down) buttons.
Press the CH SEL button on the remote
controller until CENTER is selected
and use the LEVEL π or † button to
adjust the center speaker level to match
the front left and right speaker levels.
Then press the CH SEL button on the
remote controller to select REAR and
use the LEVEL π or † button to
adjust the levels of the rear speakers.
If the center mode is set to PHANTOM,
only REAR can be selected by the CH
SEL buttons.
5. Press the TEST TONE button again
and stop the pink noise.
6. Use the DELAY TIME button to set
the delay time.
(Refer to page 18 for details.)
PHANTOM