Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for KitchenAid KUDD01DSSS0
Summary of Contents for KitchenAid KUDD01DSSS0
- Page 1 APPLIANCES 8546448 528138/8546448...
-
Page 2: Drawer Dishwasher Safety
Table of Contents lnstaBtation instructions ......Prepare Cabinet Opening ......Drawer Dishwasher Safety ......Ebctrical Connection ....... lnstaIBation Requirements ......if Installing Fbxibte Trim Pieces ....... Tools and Parts ........Install Dishwasher ......... Location Requirements ......Install Drain Hose ......... Water Supply Requirements ...... -
Page 3: Installation Requirements
INSTALLATION REQUIREMENTS IMPORTANT: Observe all governing codes and ordinances. Gather the required tools parts before starting Failure to meet codes and ordinances could lead to fire or instalhtion, Read and follow the instructions provided with electrical shock. any tools listed here, Proper installation is your responsibility: Tools needed:... - Page 4 Cabinet dimensions/requirements For dishwasher: moisture [] Not water line with 4.3-145 psi (30-1000 kPa) water pressure. protection tape [] 120°F (48.8°C) water at dishwasher. [] An easily accessible valve with 3/8" compression fitting must be installed in the hot water supply line. 4 ,_ (10cm) 32-5/16 "- 34-5/8"...
-
Page 5: Recommended Ground Method
Garbage Disposer: Recommended ground method Ifyouplan toinstall a garbage disposer, anadditional separate This appliance must b egrounded. This appliance isequipped 120-volt, 60Hz, A C-only, 15or20amp fused ebctrical supply i s withapower s upply c ordhaving 3 prong g round p lug. T o required. - Page 6 4, Asthedishwasher isbeing pushed i ntotheopening, slowly 6, Rotate drawer to the right onto its side and place on the pull t heinlet h ose, drain hoses a ndpower supply c ord protective cover. through t heutility hole. 5, Remove thestrap from upper drawer. Goto"IfInstalling Flexible Trim Pieces"...
-
Page 7: Electrical Shock Hazard
6. Remove thehouse w iring knockout, knockout Electrical Shock Hazard Connect ground wire to green ground screw. Failure to do so can result in death or electrical shock. 7, Run thehouse w iring through t heconduit connector (not supplied) and intothedishwasher through t heknockout opening, 11. - Page 8 17, U se theside cutting pliers t ocutthecable tiesecuring the 22, As the dishwasher is being pushed into the opening, slowly hoses a ndpower supply c ord totheback ofthedishwasher. pull the inlet hose and drain hoses through the utility hole. Let the house wiring gather behind the dishwasher.
- Page 9 Rotate the drawer to the right onto its side and place on the Choose attachment option protective cover. Option 1: Side attachment 1. The dishwasher side attaching tabs are accessed through holes in the sound insulation. IMPORTANT: For best installation, use all four attaching tabs. 2.
- Page 10 Option 2: Top attachment If the top attaching brackets are used, open the top drawer Option 2: Garbage disposaB connection slightly: 1, Route the drain hoses as shown and press the hoses into the drain hose support, Screw the top attaching brackets to the underside of the...
- Page 11 5. Attach thedrainhose connector totheairbreak using thesupplied h ose clamp, air break drain hose Remove front panels from and discard all shipping connector material. On the shorter front panel (lower drawer), remove tape securing the connector and wires. Discard tape. waste Connect the end of the medallion...
- Page 12 Remove any rough edges by sanding smooth, Option1:Insta{Istandardtoe pane{ Partially open bottom drawer. Position toe panel behind door NOTI=S: Depending oncountertop height, youmay nothave to and slide onto the underside of tub. trimthetoepanel. Rugs p laced infront o fdishwasher could interfere with toe panel clamping toepanel.
- Page 13 Prepare the custom front panels to specifications shown. Option 2: Install custom front panels Mount the handle to the custom panel.The screws must not extend beyond the back surface of the panel. (Handle Custom front panem dimensions is customer supplied, location is customer preference.)
- Page 14 10,LaythemetaH p ilate o ntheback ofthecustom front 15, Line up the bracket holies with the pin holies and repHace panel each pin so that the pin Hine is vertical 11,AHign thecenterHine marked o nthecustom paneH w iththe diamond shape andnotchinthemetaH p ilate t o center t he metaH p ilate h odzontaHHy, AHign t hehodzontaH Hine w iththe...
- Page 15 6. Ifneeded, youmay simply p ush thetoepanel back orforward onthemounting rail. 7. With aPhillips s crewdriver, tighten t hetoepanel clamping screws o nbothsides. toe panel clamping mounting rail screw 8. Plug in dishwasher or reconnect power. 1. Check to be sure all parts are now installed. If there is an extra part, go back through the steps to see which step was skipped.
- Page 16 Part No. 8546448 © 2004 KitchenAid ® Registered trademark/TM trademark of KitchenAid, U.S.A., Printed in U.S.A. KitchenAid Canada Hcensee in Canada Benton Harbor, Michigan 49022 10/2004...