Check The Rear Brake Fluid Level; Refilling The Rear Brake Fluid Reservoir; Checking The Rear Brake Pads - KTM 640 LC4 ADVENTURE 2003 Owner's Manual

1
2
4
5
Changing the basic position of the brake pedal *
The basic setting of the foot brake pedal can be changed by turning the end
A
1
stop roller
must be set.
Measured on the outside, the foot brake pedal must have 3-5 mm of free
play, before the push rod can move the piston in the brake cylinder (to be
recognised from the resistance on the foot brake pedal).
To keep the stop roller from turning while tightening, insert a hexagon
wrench in bore
I
F THIS CLEARANCE IS MISSING
THE BRAKE PADS BEGIN TO RUB
3-5mm
COMPLETELY IN EXTREME CASES
Checking rear brake fluid level
The reservoir for the rear disc brake is located on the left-hand side of the
vehicle next to the carburetor carburetor connection boot. The brake fluid
level may not drop below the „MlN" marking when the vehicle is in an
upright position.
I
F THE BRAKE FLUID LEVEL DROPS BELOW THE MINIMUM EITHER THE BRAKE SYSTEM HAS A
LEAK OR THE BRAKE PADS ARE COMPLETELY WORN DOWN
KTM
AUTHORIZED

Refilling the rear brake fluid reservoir*

When the brake fluid level has dropped to the MIN mark, you need to refill
the brake fluid reservoir.
For easier access to the brake fluid reservoir it is recommended to remove
the hexagon screw
the illustration. Remove plug
DOT 4 (Motorex Brake Fluid DOT 4) up to the „MAX" mark. Replace rub-
ber boot and plug. Overflown or spilled brake liquid must be rinsed off with
water. Mount the screw and fix the brake fluid reservoir to the frame,
always making sure to prevent kinks in the connecting hose.
3
– N
EVER USE
. S
COLOR EALS AND BRAKE HOSES MUST BE ESPECIALLY ADAPTED TO IT
– S
TORE BRAKE FLUID OUT OF REACH OF CHILDREN
– B
RAKE FLUID CAN CAUSE SKIN IRRITATION
YOU GET BRAKE FLUID IN YOUR EYES
A DOCTOR
– D '
ON T LET BRAKE FLUID GET IN CONTACT WITH PAINT
.
REMOVER
– U
SE ONLY CLEAN BRAKE FLUID TAKEN FROM A TIGHTLY SEALED CONTAINER

Checking the rear brake pads

min.
The brake pads can be inspected from the rear. The thickness of the linings
may not be less than 1 mm (0.04 in).
1 mm
A
T THEIR MOST WORN POINT BRAKE PAD LININGS SHOULD NOT BE THINNER THAN
OTHERWISE THEY COULD LEAD TO BRAKE FAILURE
HAVING YOUR BRAKE PADS CHANGED
I
F THE BRAKE PADS ARE REPLACED TOO LATE SO THAT THE LINING IS PARTLY OR ENTIRELY
,
WORN AWAY
,
DISC IMPARING THE BRAKING EFFECT AND DESTROYING THE BRAKE DISC
2
. Using the push rod , the free play on the foot brake pedal
A
.
! CAUTION
,
PRESSURE ACCUMULATES IN THE BRAKING SYSTEM AND
. T
HE BRAKING SYSTEM OVERHEATS AND CAN FAIL
.
WARNING
.
DEALER IMMEDIATELY
3
. Then move the container outwards as indicated in
4 with rubber boot
WARNING
DOT5 ! I
BRAKE FLUID T IS BASED ON SILICONE OIL AND OF A PURPLE
. A
VOID CONTACT WITH SKIN AND EYES
,
RINSE WITH PLENTY OF WATER AND CONSULT
CAUTION
!
WARNING
. F
.
CAUTION
!
THE STEEL COMPONENTS OF THE BRAKE PAD WILL RUB AGAINST THE BRAKE
!
. I ,
N THIS CASE CONSULT AN
5 and add brake fluid
.
.
!
,
IT IS AN EFFECTIVE PAINT
.
1
MM
'
OR YOUR OWN SAFETY DON T PUT OFF
!
.
29
. I
F
,