Honeywell Micronik 200 Specification Data page 3

CONTROL AND CONFIGURATION PARAMETER
The controller includes two groups of settings (A and B) for control and configuration parameters that are automatically
selected during programming. For parameter Ctrltyp = Lo setting A is selected and for parameter Ctrltyp = Hi setting B is
selected.
Control Parameter
No. Name
P.01 W1 Main setpoint for input T1
P.02 Wlim Limit setpoint (low or high) for input T2
P.03 Wcomp Compensation changeover point for input T3
P.04 Wi Winter compensation authority
P.05 Su Summer compensation authority
P.06 Wcas Submaster or cascade setpoint
P.07 Rcas Cascade reset span adjustment
P.08 Xp1 Throttling range (main control loop) T1
Throttling range (cascade or limit control loop)
P.09 Xp2
T2
1)
P.12 tr1 Reset time (main control loop) T1
1)
P.13 tr2 Reset time (cascade or limit control loop) T2
P.15 Ystart Start point for mid range shift of output Y1
P.16 SOFFS Offset of main setpoint in Standby mode
P.17 T1Cal Calibration of temperature sensor T1
P.18 T2Cal Calibration of temperature sensor T2
P.19 T3Cal Calibration of temperature sensor T3
P.21 RuntimeY1 Actuator run time for Y1
P.24 NightLow Night low limit against temperature extremes
P.25 NightHigh Night high limit against temperature extremes
P.26 NOFFS Offset of main setpoint in Night mode
Config. Parameter
No. Name
2)
C.04 Ctrltyp Lo = 0...50°C, Hi1 = 0...130°C, Hi2 = 0...130°C
0 = internal (default), 1 = 5 K (953...1053 τ), 2 = 5 K (100 kτ...0 τ),
C.05 CPATYP 3 = 15 ... 30C (10...20 kτ), 4 = 5 K (0...10 kτ),
5 = 15 ... 30C (0...100 kτ), 6 = 0...50C or 0...130C (0...100 kτ)
0= floating, 1= 2 stage ON/OFF, 2= 3 stage ON/OFF, 3 = pwm, 4 = unconfig.
C.08 Y1Mode
(safe state is configured prior to controller's start-up)
C.12 T2ext 0 = T2 installed
C.13 LimTyp 0 = Low limit
C.14 Senstyp 0 = Auto detection
Output Y1 used for:
C.15 Y1CTRF
C.16 AddHour Adjusts the month for winter/summer time change: 0 (disabled) = Min. 12 = Max.
C.17 SubHour Adjusts the month for summer/winter time change: 0 (disabled) = Min. 12 = Max.
3)
C.18 PSTG_H Prestart gradient for heating:
3)
C.19 PSTG_C Prestart gradient for cooling:
C.21 Adapt Optimum Start Self Adaption speed:
2)
C.22 Adr Serial communication address:
C.23 0 = No default programming
DefProg
1)
for tr > 2 min resolution = 0.5 min , for tr < 2 min
2)
actual value will not be changed during reset to default parameter
3)
can be overwritten by controller for self-adaption purposes, resolution = 0.01 K/min
Parameter Description
Values
1 = Initiates default programming
resolution = 10 sec
R7426A TEMPERATURE CONTROLLER
Setting A / Setting B
Low
0 50/130
5 / 30 50/130
-5
-350
-100
OFF, 0 50/130 20/OFF
0
0.5
0.5
OFF, 20 s
OFF, 20 s
-20
0
-20
-20
-20
6
OFF, 8 19 / 80
OFF, 21
0
1 = T1 signal used for T2
1 = High limit
1 = NTC sensor type
0 = cooling, 1 = heating
2 = summer/winter changeover
0 (disabled) = Min. 2 = Max.
0 (disabled) = Min.
0 = Min. 100 = Max.
0 = Min. 255 = Max.
3
Reso-
lution
High
Default
21 / 70 0.5
16 / 90 1
40 20 1
+350 0 2
+100 0 1
0.5
40 10 0.5
40 2 0.5
40 10 0.5
20min OFF 10/0.5
20min OFF 10/0.5
+20 0 0.5
10 2 0.1
+20 0 0.1
+20 0 0.1
+20 0 0.1
180 60 1
OFF 1
40 OFF 1
30 5 / 20 0.1
Default
A / B
Lo
0
4
0
0 / 1
0
0 / 1
3
10
0
2 = Max. 0
50
254
0
EN0B-0299GE51 R0104
Unit
C
C
C
%
%
C
K
K
K
sec/min
sec/min
K
K
K
K
K
sec
C
C
K
Unit
month
month
K/min
K/min
%