Haier HWM75-0528 A User Manual page 7

b
Steps of using the operation buttons and
description of the steps
Program
STANDARD
SOAK HEAVY
GENTLE
SAVE
COTTON
INDICATION OF PROCESS
SINGLE WASH
(NO CHOOSING)
RINSE SPIN
SOAK
SINGLE SPIN
WASH
TUB CLEAN
RINSE
AIR DRY SPIN
START
PAUSE
1.Push "POWER"button to switch on the power
2.Push "PROGRAM/RESERVE" button to select
suitable automatic program
After the power is switched on, "standard" is automatically set. To select other full-auto program, please push
the "PROGRAM/RESERVE" button till the corresponding indicator is on. Refer to the "PROGRAM/RESERVE
button" on Page 11.E.g
For instance:select "SAVE" program for small quantity of laundries with light soil.
Program select
Program
The display of digitron Application
01 STANDARD Common washing
02 SOAK HEAVY Washing for coverlet bigger laundries
03
GENTLE Washing the woollen
04 SAVE Washing for normal laundries
COTTON
05 Washing the cotton textiles
06 SINGLE WASH
Reusing the washing detergent
Washing the cloth washed by hand
07 RINSE SPIN
(first draining, then spinning)
Only spinning the cloth wet or washed by
08 SINGLE SPIN
hand (first draining, then spinning)
The spinning time is the same to the single spin,
09
TUB CLEAN
but spinning in lower
Avoid growing mildew on the outer tub and the
10
AIR DRY
inner tub
12
POWER
TIME REMAINED(MINUTES)
ON/OFF
WATER
RESERVE(HOURS LATER) LEVEL
Digital display Digital display Digital display Digital display Digital display Digital display Digital display Digital display
Fuzzy logic control Fuzzy logic control Fuzzy logic control Fuzzy logic control Fuzzy logic control Fuzzy logic control Fuzzy logic control Fuzzy logic control
10 water level selection 10 water level selection 10 water level selection 10 water level selection 10 water level selection 10 water level selection 10 water level selection 10 water level selection
PROGRAM/RESERVE
POWER
ON/OFF
PROGRAM/RESERVE
The running process
(the digitron displays the running process)
WASH( ) RINSE( ) SPIN( )
SOAK( ) WASH( ) RINSE( ) SPIN( )
silk textiles SPIN( )
WASH( ) RINSE( )
RINSE( ) SPIN( )
WASH( )
WASH( )
RINSE( ) SPIN( )
WASH( )
RINSE( ) SPIN( )
SPIN( )
SPIN( )
SPIN( )
How to change the direction of the drain hose
1.Dismantle the rear cover of the washing machine.
2.Put down the drain hose .Take off the drain hose
frame as indicated in Figure 1.Take the drain hose into
the cabinet ,then nip the drain fixing clamp to make it
deviated from the clip,the other hand is used to put down
the drain bushing,as indicated in Figure 2,3.
Drain hose
Drain hose support Drain bushing
Figure 1
Figure 2
Cabinet
Inner Outer
Push
Drain bushing
Take down
Drain hose fixing
clamp
Figure 3
Push
Remarks: in order to make sure of the correct of installation, it is suggested to change the direction of the drain hose
with our company serviceman .
Usage the drain hose
The drainage shall be smooth with the drain hose.
1. The height of the drain hose shall be less than 10cm,
or the drainage will not be smooth, and cost such long
time that the machine may stop at mid way.
2.Do not step on or press the drain hose.
3. If the drain hose is too long, cut it at mid point. To make
smooth drainage, cut the front end of the hose slantingly.
3.Dismantle the drain outlet protecting cover at the other side,
(the way is the same as the drain bushing),then install the drain
bushing, as indicated in Figure 4.
4.Extend the drain hose from the other side. Fix the drain hose
with drain hose frame onto the cabinet, as indicated in Figure 5.
Drain outlet
protecting cover
Figure 5
Figure 4
Drain bushing
5.Install the drain outlet protecting cover to the other side,
as indicated in Figure 6
Figure 6
4.If extra drain hose is needed, please make separate
purchase. The inner diameter of the extra hose shall
not less than 30mm, and the length shall not exceed
1.5m.
5.If the extra hose is too long, cut it either at A or at B.
5