ELECTRICAL REQUIREMENTS EXHAUST SYSTEM REQUIREMENTS ELECTRICDryer Use only 4 inch (10.2 cm) diameter (minimum) rigid or flexible metal duct and approved vent hood which has a swing-out CIRCUIT- Individual 30 amp. branch circuit fused with 30 damper(s) that open when the dryer is in operation. When the amp.
Connect an inclined or digital manometer between the Do not allow combustible materials {for dryer and the point the exhaust connects to the dryer. example: clothing, draperies/curtains, paper) to come in Set the dryer timer and temperature to air fluff (cool down) contact with exhaust...
5. A 1/8inch (0.32 N.RT. plugged tapping, accessible for test gauge connection, MUST be installed immediately upstream of the gas supply connection to the dryer. 6. The dryer MUSTbe disconnected from the gas supply piping system during any pressure testing of the gas supply piping system at test pressures in excess of 1/2 psig (3.45 kPa).
MOBILE HOME INSTALLATION UNPACKING I. Using the four shipping carton corner posts (two on each 1. Dryer MUST be exhausted outside (outdoors, not beneath side), carefully lay the dryer on its left side and remove foam the mobile home) using metal ducting that will not support shipping base.
ELECTRICAL INSTALLATION ALL ELECTRICDryers Canadian ELECTRICDryer The following are specific requirements Improper connection of the equipment grounding conductor can result in a risk of electrical shock. Check with a proper and safe electrical installation of your dryer. Failure to follow these instructions can create electrical shock and/...
ELECTRICAL CONNECTIONS ELECTRICAL CONNECTIONS FOR 4-WIRE SYSTEM FOR 3-WIRE SYSTEM Non-Canadian ELECTR/CDryer Non-Canadian ELECTR/CDryer 1. Remove the screws securing the terminal block access cover 1. Remove the screws securing the terminal block accesscover and the strain relief mounting bracket located on the back of and the strain relief mounting bracket located on the the dryer upper corner.
INSTALLATION I. GAS CONNECTION (Gas dryers only) If your dryer does not operate, please review the "Avoid a. Remove the shipping cap from gas pipe at the rear of Service Checklist" located in your Owner's Guide before the dryer. calling for service. NOTE: DO NOTconnect the dryer to L.R gas service without Placethese instructions in a location near the dryer for futu re...
Page 11
Tabla de Materias Requerimientos de instalaciOn preliminares ........................... Requerimientos elOctricos ..............................Requerimientos del sistema de escape..........................12-13 Requerimientos del suministro de gas............................ UbicaciOn de su secadora ..............................Dimensiones para la instalaciOn ............................InstalaciOn en casas mOviles..............................Desembalaje ..................................Puerta reversible ................................InstalaciOn elOctrica ................................
REQUERIMIENTOS ELECTRICOS REQUERIMIENTOS DEL SISTEMA DE ESCAPE Utilicesolamenteductosmetalicos rigidosoflexibles de 4" Secadoras ELECFR/CAS (10,2 cm) de diametro (minim@ y una caperuza de salida de uso aprobado, con registros que giren hacia afuera que seabren cuando CIRCUITO- Circuito derivado individual de 30 amperes, con fusibles la secadora se encuentra en funcionamiento.
Riesgo de explosi6n. No instale la secadora Sedebe utilizar solamente conductos metalicos rigidos. donde se guarda gasolina u otros materiales inflamables. Si la Una salida del sistema vertical en el techo, puede exponerle a un corriente de aire descendente y disminuir asi su capacidad secadora se instala en un garage, ella debe estar pot Io menos 18 de exhaustaciOn.
4. Se requiere como minimo una abertura de 120 pulgadas cua- UBICA CION DE SU SECADORA dradas (774,2 cm2), dividida equitativamente para la parte NO INSTALE SU SECADORA: superior e inferior de la puerta. Cuando se instala una puerta, I. En un lugar donde puede haber goteos de agua o quede es necesario proveer aberturas para el aire.
MODELOS DE DEBAJO MODEL OS A UTONOMOS DE MOSTRADOR Y APILADORES CON CONSOLA SUPERIOR DIMENSIONES PARA LA INSTALACION DIMENSIONES PARA LA #NSTALAC!ON 26 7/8" (68,3 cm) CONEXION ELE:CTRICA CONEXION ELECTRICA BAJO MOSTRADOR 34 5/8" (87,9 cm) 29/16" (6,5cm) 2 9/16" (6,5 cm) 9F--t 43 5/8"...
INSTALACION EN CASAS MOVILES DESEMBALAJE 1. Eltubo de escapede la secadora DEBEserinstalado hacia el exterior 1. Utilizando las cuatro esquineras de embarque de la caja (Elescape debe coloca rseen la parte exterior y no debajo de la casa de carton (dos a cada lado), coloque cuidadosamente la secadora sobre el costado izquierdo y saque la base de mOvil.)Debe usarseducto de metal que no seacombustible.
INSTALA CION ELECTRICA Para una secadora conectada permanentemente: I. La secadora DEBE ser conectada a un sistema de cableado TODAS/assecadorasELECTRICAS metalico permanente, puesto a tierra; o se debe instalar un conductor de puesta a tierra deequipojunto con Iosconductores ¥__ Los siguientes requerimientos son especificos del circuito y conectarse al borne de puesta a tierra del equipo...
CONEX!ONES ELECTRICAS PARA CONEXIONES ELECTRICAS PARA UN SISTEMA TETRAFILAR UN SISTEMA TRIFILAR Secadoras ELECTR/CASNo canadienses SecadorasELECTR/CASNo canadienses 1. Saque lostorn illosque sujetan la cubierta de accesodel tablero de bornes y el soporte de montaje del anclaje de cable situado I. Saque los torn illos que sujetan la cubierta de accesodel tablero en la esquina superior en la parte trasera de la secadora.
INSTALAOON 1. CONEXION DEL GAS (Secadoras a gas solamente) 7. Si su secadora no funciona, consulte la secci6n "Lista de a. Saque la tapa de embarque de la tuberia de gas de la Control de Averias" que se encuentra en su Manual del secadora situada en la parte trasera.