Advertisement
Available languages
Available languages
Important
Notes
to the
Installer
1. Read all instructions contained in these installation
instructions before installing range.
2. Remove all packing material from the oven
compartments before connecting the electrical supply to
the range (see "Preparation ", page 5).
3.Two anti-tip brackets, located inside the oven cavity MUST
be installed (see "Anti-Tip Bracket Installation", page 8).
4.Observe all governing codes and ordinances.
5. Be sure to leave these instructions with the consumer.
Important
Note
to the
Consumer
Keep these instructions with your owner's guide for future
reference.
IMPORTANT
SAFETY
INSTRUCTION
Installation of this range must conform with local codes
or, in the absence of local codes, with CAN/CGA-B149.1
and CAN/CGA-B149.2
standards.
This range has been design certified by the American
Gas Association. As with any appliance using gas and
generating heat, there are certain safety precautions you
should follow. You will find them in the Use and Care
Guide., read it carefully.
• Be sure your range is installed
and grounded
properly
by a qualified
installer
or service
technician.
o All ranges can
tip.
Injury to
persons could
result.
Install anti-tip
device packed
with range.
To reduce the risk of tipping
of the range, the range
must be secured by properly
installed anti-tip bracket(s)
provided with the range.
To check if the bracket(s) is
installed properly, remove
the lower panel or stor-
age drawer and verify that
the anti-tip bracket(s)is
engaged.
This range must be electrically
grounded
in
accordance
with
local codes or, in their absence,
with CSA standard
C22.1, Canadian
Electrical
Code, Part 1.
The installation of appliances designed for
manufactured (mobile) home installation must conform
with Manufactured
Home Construction
and Safety
Standard, title 24CFR, part 3280 [Formerly the Federal
Standard for Mobile Home Construction
and Safety,
title 24, HUD (part 280)] or when such standard
is not applicable, the Standard for Manufactured
Home Installation 1982 (Manufactured
Home Sites,
Communities and Setups), ANSI Z225.1/NFPA 501A-
latest edition, or with CAN/CSA-Z240 MH.
Make sure the wall coverings
around
the range
can withstand
the heat generated
by the range.
Before installing
the range in an area covered
with linoleum
or any other synthetic
floor
covering,
make sure the floor
covering
can
withstand
heat at least 90°F (32.2 °C ) above
room temperature
without
shrinking,
warping
or
discoloring,
Do not install the range over carpeting
unless you place an insulating pad or sheet of 1/4"
(0.6 cm) thick plywood between the range and
carpeting.
Do not obstruct
the flow of combustion
air at the
oven vent nor around the base or beneath
the
lower
front panel of the range. Avoid touching the
vent openings or nearby surfaces as they may become
hot while the oven is in operation. This range requires
fresh air for proper burner combustion.
Never leave children
alone or
unattended
in the area where
an appliance
is in
use, As children grow, teach them the proper, safe use
of all appliances. Never leave the oven door open when
the range is unattended.
Stepping,
leaning
or sitting
on the
door(s) or drawer
of this range can result in serious
injuries
and can also cause damage
to the range.
• Do not store items of interest
to children
in
the cabinets
above the range. Children could be
seriously burned climbing on the range to reach items.
To eliminate
the need to reach over the surface
units, cabinet storage space above the units
should
be avoided,
Adjust surface burner flame size so it does not
extend
beyond
the edge of the cooking
utensil,
Excessiveflame is hazardous.
Do not use the oven as a storage space. This
creates a potentially hazardous situation.
Never use your range for warming
or heating
the
room, Prolonged use of the range without
adequate
ventilation can be dangerous.
Do not store or use gasoline
or other flammable
vapors and liquids
near this or any other
appliance,
Explosions or fires could result.
In the event of an electrical power outage, the surface
burners can be lit manually. To light a surface burner,
hold a lit match to the burner head and slowly turn
the Surface Control knob to Lite. Use caution when
lighting surface burners manually.
• Reset all controls
to the "off"
position
after using
a programmable
timing
operation,
This appliance
is equipped
with
a
4-prong
grounding
plug for your protection
against
shock hazard, and should
be plugged
directly
into a
properly
grounded
receptacle.
Do not cut or remove
the ground
prong from this plug,
Advertisement
