Gas Conversion - GE ZGP366N Installation Instructions Manual

Installation Instructions for Gas Conversion
ADJUST BURNER FLAMES
Normally, burners do not need further adjustment.
Hake adjustments only when necessary.
A. Turn on the gas. Plug in electrical cord.
B. Turn all burners on highest setting and check
the flames. They should be blue in color. When
using LP gas, the flames may have some yellow
tipping at the ends of the flame. Foreign particles
in the gas line may cause on orange flame at first,
but this will soon disappear.
C. Turn the burner knob to "LO" while observing the
flame.
Adjust the setting of the upper row of flames using
the valve bypass screw as follows:
Adjustments must be made with two other burners
in operation on a medium setting. This prevents the
upper row of flames from being set too low, resulting
in the flame being extinguished when other burners
are turned on.
D. To adjust the flame, remove the knobs. Insert a small
fiat-blade screwdriver into the hole in the center of
the valve stem to engage screw.
• If the flames are too small or flutter,
turn the screw counterclockwise.
• If the flames are too large, turn the screw
clockwise.
E. Make the adjustment by slowly turning the screw
until flame appearance is correct.
HODEL
ZGP48
ZGP36
ZGP304
ZGP304
ALL
ALL
ZGP48/
ZGP36
ZGP30
ZGP48
ALL
ZGP48
BURNER OUTPUT RATINGS: BTU/HR
NG (Natural) Gas, 5" W.C.P. LP (Propane) Gas, 10" W.C.P.
BURNER BTU ORIFICE SIZE ID MODEL BURNER BTU ORIFICE SIZE ID
RATE RATE
ALL SURF. Main 16,800 0.075" (1.90mm) 190XN ZGP48 ALL SURF. Main 13,800 0.043" (1.08mm) 108XL
BURNERS Simmer 1,200 0.002" (0.51mm) 51SL ZGP36 BURNERS Simmer 1,200 0.013"(0.34mm) 34SL
Main 16,800 0.075" (1.90mm) 190XN Main 13,800 0.043"(1.08mm) 108XL
RFBURNER ZGP304 RFBURNER
Simmer 1,200 0.002" (0.51mm) 51SN Simmer 1,200 0.013"(0.34mm) 34SL
Main 8,800 0.050" (1.26mm) 126HXN Main 7,900 0.033"(0.84mm) 84XL
RR,LR,LF Simmer 1,200 0.002" (0.51mm) 51SN ZGP304 RR, LR,LF Simmer 1,200 0.013"(0.34mm) 34SL
GRILL 15,000 0.0689"(1.75mm) 0.069 ALL GRILL 14,000 0.047"(1.19mm) 0.047
GRIDDLE 18,000 0.076" (1.93mm) 0.076 ALL GRIDDLE 16,000 0.047"(1.19mm) 0.047
BAKEMAIN 0.0886" ZGP48/ BAKEMAIN 0.0571"
24,500 0.089 23,000 0.055
(2.25mm) ZGP36 (1.35mm)
BAKEMAIN 23,500 0.0866"(2.20mm) 0.087 ZGP30 BAKEMAIN 21,500 0.0531"(1.35mm) 0.053
BAKECOMPANION 10,500 0.0531"(1.35mm) 0.053 ZGP48 BAKECOMPANION 10,000 0.0374"(0.95mm) 0.037
BROIL MAIN 12,500 0.063" (1.60mm) 160 ALL BROIL MAIN 11,500 0.041"(1.04mm) 104
BROILCOMPANION 9,000 0.052" (1.32mm) 132 ZGP48 BROIL COMPANION 9,000 0.0360"(0.91mm) 91
I nce the conversion is complete ond checked, fill out the conversion label ond affix the label neor the rating label. For ranges,
place the label beneath the control panel. Forrangetops, place the label on the bottom of the unit.
I