Advertisement
Available languages
Available languages
ALLURE ® QS3 SERmES
RANGE
HOOD
®
7
Page
6
NONoDUCTED FILTERS
If hood is to be installed Non-Ducted:
Purchase a set of (2) Non-Ducted Filters from your local
distributor or retailer and attach them to the aluminum mesh
fiJters.
3. Remove and inspect fuse. if it is not open (blown), additional
diagnostics need to be done.
4. InstalI new fuse.
5. Re-assemble
air chute, light wire harness, bottom panel, and
filters.
6. Turn on power and check hood/control operation.
NOTE:
For models that are installed in the nomducted mode, the
most effective operation is achieved at speeds 1 and 2.
These
speeds
provide
the most efficient
and quiet
operation
during cooking, while maximizing the benefits
of the recirculating filtration system.
Fan: 4 push button switches. Push any button to select one of the
four fan speeds. Press another button to change fan speed. Push
the same button to turn fan off. A light above each fan button indi-
cates the fan speed.
Lights:
Press "on/off" button and lights wiII come on at their previ-
ous Iight level
Press button again to turn lights off. To increase
light Ievel, press the '%" button. To reduce light level, press the "-"
button. There are 3 light levels to seIect.
DeBay Off: While fan is running, press the "delay" button to allow
the fan to run for 10 minutes and then turn itself off.
FHter Change Indicator:
The Iight above "fiIter" will come on when
it is time to clean your grease filters or check your non-ducted
fiIters. After replacing the cleaned, or new filters, press the "filter"
button to turn off the indicator light.
Heat Sentry System:
Your range hood is equipped with an ad-
vanced Heat Sentry system.
The advanced Heat Sentry system monitors temperature
and au-
tomatically adjust the fan to the appropriate setting.
1) if the fan is on, the Heat Sentry system will increase the fan
setting when the temperature
is elevated,
if the temperature
continues to rise, the Heat Sentry system wilI continue to in-
crease the fan setting until the temperature
is stabilized or re-
duced. The flashing light above the fan button shows the Heat
Sentry system fan setting. Once the temperature
has reduced,
the Heat Sentry system will change the fan to the original set-
ting.
2) if the fan is on or off, the Heat Sentry system will automatically
turn the fan on at its highest speed when the temperature
is
above norma!. When the Heat Sentry system is on, the light
above the fan button B (Boost) wilI flash on and off. After the
temperature
has lowered to normal, the fan wiII change to the
setting prior to the Heat Sentry turning on.
Fuse: The hood control contains a fuse to protect it from power
surges, if the fuse has opened (bIown), the green fan-Ievel indica-
tors wilI operate
properly
when the fan buttons/switches
are
pressed - but the fan and lights will not turn on.
The fuse is a 5 x 20 ram, 10Amp,
Fast-Acting, 125V (rain.). Com-
mon manufacturer
and
part numbers
are: Littlefuse,
217010;
Bussmann, GMA10A; Wickmann,
1942100. Radio Shack, Digikey
(1-800-344-4539),
and most electronic supply stores have them
in stock.
To replace the fuse:
1. Disconnect power at service entrance.
2. Remove filters, bottom panel, light wire harness, and air chute.
_
ARNING: To reduce the risk of electric
shock,
disconnect
from power suppJy before cleaning.
Amuminum mesh filters:
Clean frequentIy using hot water and a
mild detergent. Filters are dishwasher
safe.
Ohareoam filters:
Clean filter surfaces frequently with a damp cloth
and a mild detergent. DO NOT immerse filters in water or put in
dishwasher.
The special "Clean Sense" feature indicates
when
the filter is to be replaced. The blue and yellow strips wilI blend to
green
when it is time to change the filter. The "Clean Sense"
feature works best when facing toward the cooking surface.
To clean hood: Remove filters. Use a damp cloth and a mild deter-
gent to wipe all greaseqaden surfaces. Do not use abrasive cloth,
steel wool pads, or scouring powder on the Tefion®-coated bottom
cover or on any painted surface. Use care when cleaning blower
wheel - it must not become bent or misaligned.
DO NOT ALLOW
WATER TO ENTER MOTOR. Make sure al! surfaces are com-
pletely dry before re-installing filters and restoring power.
Motor is permanently lubricated. Do not oiI or disassemble motor.
Teflon_ is a registered trademark of DuPonL
Advertisement
