Sign in today to find solutions:

Don't have an account? Sign up

Broan ALLURE QS3 User Manual

Broan ventilation hood user manual.

 
ALLURE
®
QS3 SERIES
RANGE HOOD
READ AND SAVE THESE INSTRUCTIONS
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO
PERSONS, OBSERVE THE FOLLOWING:
1. Use this unit only in the manner intended by the manufacturer. If you have
questions, contact the manufacturer at the address or telephone number
listed in the warranty.
2. Before servicing or cleaning unit, switch power off at service panel and
lock the service disconnecting means to prevent power from being
switched on accidentally. When the service disconnecting means cannot
be locked, securely fasten a prominent warning device, such as a tag, to
the service panel.
3. Installation work and electrical wiring must be done by a qualified
person(s) in accordance with all applicable codes and standards, includ-
ing fire-rated construction codes and standards.
4. Sufficient air is needed for proper combustion and exhausting of gases
through the flue (chimney) of fuel burning equipment to prevent backdraft-
ing. Follow the heating equipment manufacturer's guideline and safety
standards such as those published by the National Fire Protection As-
sociation (NFPA), and the American Society of Heating, Refrigeration and
Air Conditioning Engineers (ASHRAE), and the local code authorities.
5. When cutting or drilling into wall or ceiling, do not damage electrical wiring
and other hidden utilities.
6. To reduce the risk of fire or electric shock, do not use this range hood
with an additional speed control device.
7. Ducted fans must always be vented to the outdoors.
8. To reduce the risk of fire, use only metal ductwork.
9. Use with approved cord-connection kit only.
10. This unit must be grounded.
TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:
1. Never leave surface units unattended at high settings. Boilovers cause
smoking and greasy spillovers that may ignite. Heat oils slowly on low or
medium settings.
2. Always turn hood ON when cooking at high heat or when cooking flaming
foods.
3. Clean ventilating fans frequently. Grease should not be allowed to
accumulate on fan or filter.
4. Use proper pan size. Always use cookware appropriate for the size of
the surface element.
TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A
RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING:*
1. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray,
then turn off the burner. BE CAREFUL TO PREVENT BURNS. If the
flames do not go out immediately, EVACUATE AND CALL THE FIRE
DEPARTMENT.
2. NEVER PICK UP A FLAMING PAN — You may be burned.
3. DO NOT USE WATER, including wet dishcloths or towels - violent steam
explosion will result.
4. Use an extinguisher ONLY if:
A. You know you have a Class ABC extinguisher and you already know
how to operate it.
B. The fire is small and contained in the area where it started.
C. The fire department is being called.
D. You can fight the fire with your back to an exit.
* Based on "Kitchen Fire Safety Tips" published by NFPA.
!
FOR DOMESTIC COOKING ONLY
!
CAUTION
1. For general ventilating use only. Do not use to exhaust hazardous or
explosive materials and vapors.
2. To avoid motor bearing damage and noisy and/or unbalanced impellers,
keep drywall spray, construction dust, etc. off power unit.
3. For best capture of cooking impurities, your range hood should be
mounted so that the top of the hood is 24-30" above the cooking surface.
4. Please read specification label on product for further information and
requirements.
Installer: Leave this manual with
the homeowner.
Homeowner: Operating and
Cleaning information on page 6.
NOTE
If hood is to be installed Non-Ducted:
Purchase a set of (2) non-ducted filters from your
local distributor or retailer and attach them to the
aluminum mesh filters.
TABLE OF CONTENTS
This manual is divided into sections as follows:
"PREPARE HOOD LOCATION"
Run ductwork from roof or wall cap, and electrical wiring from service
panel - to installation location
"PREPARE THE HOOD"
Get your hood ready for installation
"CONNECT WIRING"
Make electrical wiring connections to hood
"INSTALL HOOD"
Secure hood to cabinet and ductwork - install bulbs and filters
"OPERATION"
How to use the hood controls
"CLEANING"
Keep your hood in top working condition
"SERVICE PARTS"
Part numbers and exploded view of hood components
"WARRANTY"
One-year limited warranty and how to contact us
ALLURE
QS3 SERIES
®
RANGE HOOD
Page 1
Patent No.:
US D450, 829 S
!
Next page ->

Summary of Contents

  • Page 1

    ALLURE ® QS3 SERIES RANGE HOOD READ AND SAVE THESE INSTRUCTIONS FOR DOMESTIC COOKING ONLY WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: 1. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer at the address or telephone number listed in the warranty.

  • Page 2

    PREPARE HOOD LOCATION ROOF CAP 3¼" X 10" or 7" ROUND DUCT (For vertical discharge) SOFFIT CABINET HOOD HOOD 24" - 30" ABOVE COOKING SURFACE Determine whether hood will discharge vertically (3¼” x 10” or 7” Round), or horizontally (3¼” x 10” only). For vertical or horizontal discharge, run ductwork between the hood location and a roof cap or wall cap.

  • Page 3

    PREPARE THE HOOD Remove Teflon -coated ® bottom cover from hood. Set cover and mounting screws aside. Teflon is a registered ® trademark of DuPont. TEFLON -COATED BOTTOM COVER ® (Held in place with 2 screws) Remove Damper/Duct Connector from inside the hood.

  • Page 4

    PREPARE THE HOOD TOP RECTANGULAR DUCT KNOCKOUT (Remove for 3¼” x 10” Vertical & for 7” Round Discharge) REAR RECTANGULAR DUCT KNOCKOUT (Remove for 3¼” x 10” Horizontal Discharge) Remove appropriate Duct Knockout(s) from top or back of hood. TIES SCREW METAL STRIP PLATE...

  • Page 5

    CONNECT WIRING WARNING: To reduce the risk of electric shock, make sure power is switched off at the service panel. Lock or tag service panel to prevent power from being switched on accidentally. Connect House Wiring (120 VAC) to hood. Use a piece of Cardboard to protect the cooktop, if necessary.

  • Page 6

    NON-DUCTED FILTERS If hood is to be installed Non-Ducted: Purchase a set of (2) Non-Ducted Filters from your local distributor or retailer and attach them to the aluminum mesh filters. NOTE: For models that are installed in the non-ducted mode, the most effective operation is achieved at speeds 1 and 2.

  • Page 7

    SERVICE PARTS KEY NO. PART NO. DESCRIPTION R680508 7” Round Duct Plate (includes hardware) R740013 Damper/Duct Connector (includes hardware) R602017 Screw, #8-18 x ¼ Hex* (2 in package) R334126 Motor Capacitor (includes wire nuts & hardware) R501031 Isolation Transformer R627505 Nameplate, White R627506 Nameplate, Almond...

  • Page 8

    INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. During this one-year period, Broan-NuTone will, at its option, repair or replace, without charge, any product or part which is found to be defective under normal use and service.

  • Page 9

    CAMPANA EXTRACTORA SERIE QS3 ALLURE LEA Y CONSERVE ESTAS INSTRUCCIONES PARA COCINAR DOMÉSTICO SOLAMENTE. ADVERTENCIA PARA REDUCIR EL RIESGO DE INCENDIO, CHOQUE ELECTRICO, O LESION A PERSONAS, PROCURE LO SIGUIENTE: 1. Utilice esta unidad sólo en la manera prescrita por el fabricante. Si tiene usted alguna pregunta, comuníquese con el fabricante a la dirección o el teléfono indicados en la garantía.

  • Page 10

    PREPARACIÓN DEL LUGAR DONDE SE VA A INSTALAR LA CAMPANA TAPA DE TECHO REDONDO DE 17.8 cm (para descarga vertical) PLAFÓN GABINETE CAMPANA CAMPANA De 45.7 cm a 60.9 cm SOBRE LA SUPERFICIE PARA COCINAR Determine si la descarga de la campana va a ser vertical [conducto de 8.3 cm x 25.4 cm (3 ¼”...

  • Page 11

    PREPARACIÓN DE LA CAMPANA Quite la Cubi- erta inferior recubierta de Teflón ® la campana. Coloque a un lado la cubierta y los tornillos de montaje. Teflon es una marca ® CUBIERTA INFERIOR RECUBIERTA DE comercial registrada TEFLÓN ® (Se encuentra fija con 2 tornillos) de DuPont.

  • Page 12

    PREPARACIÓN DE LA CAMPANA AGUJERO CIEGO SUPERIOR DEL CONDUCTO RECTANGULAR (Quite en el caso de descargas verti- cales de 8.3 cm x 25.4 cm (3 ¼” x 10”) o de descargas con conductos redondos de 17 .8 cm (7”) AGUJERO CIEGO POSTERIOR DEL CONDUCTO RECTAN- GULAR...

  • Page 13

    CONEXIÓN ELÉCTRICA ADVERTENCIA: Para reducir el riesgo de descar- gas eléctricas, asegúrese de apagar el interruptor de alimentación eléctrica en el panel de servicio. Bloquee o rotule el panel de servicio para evitar que alguien conecte accidentalmente la energía eléctrica. Haga la conexión eléctrica del suministro doméstico (120 VCA) en la campana.

  • Page 14

    FILTROS SIN CONDUCTOS Si la campana se va a instalar en un sistema sin conductos: Compre un juego de (2) filtros para sistemas sin conductos en la tienda distribuidora o minorista de su localidad y sujete a los filtros de malla de alumino. NOTA: En el caso de los modelos con que están instalados en la modalidad sin conductos, la operación más eficiente se logra a logra a las velocidades 1 y 2.

  • Page 15

    PIEZAS DE SERVICIO CLAVE N.º PIEZA N.º DESCRIPCIÓN R680508 Placa de conducto redondo de 7” (17.7 cm) (incluye herraje) R740013 Regulador de tiro/conectador de conducto(incluye herraje) R602017 Tornillo hexagonal, #8-18 x ¼ Hex* (2 en el paquete) R334126 Capacitor del motor (incluye tuercas para alambre y herraje) R501031 Transformador de aislamiento R627505...

  • Page 16

    Esta garantía reemplaza todas las garantías anteriores. Para calificar en la garantía de servicio, usted debe (a) notificar a Broan-NuTone al domicilio o al número de teléfono abajo, (b) dar el número del modelo y la identificación de la pieza, y (c) describir la naturaleza de cualquier defecto en el producto o pieza. En el momento de solicitar servicio cubierto por la garantía, usted debe de presentar evidencia de la fecha original de compra.

Comments to this Manuals

Symbols: 0

Latest comments:

×

Select the desired size and copy embed code

Copy your embed code and put on your site: