Table of Contents
Advertisement
BOSCH
INSTALLATION
INSTRUCTION'
MANUAL
for
Bosch Electric Built-in
Single & Double Oven Models HBN 64.J65,.166.,
BEFORE YOU BEGIN, READ THESE
INSTRUCTIONS
COMPLETELY
AND CAREFULLY
IMPORTANT:
Save these instructions for _e local electrical inspector's
nse'_
INSTALLER:
Please leave this manual w_th owner for future reference.
|
OWNER:
Please keep this manual for future reference
/
J
Advertisement
Table of Contents
Related Manuals for Bosch HBN 642A UC
Summary of Contents for Bosch HBN 642A UC
- Page 1 BOSCH INSTALLATION INSTRUCTION' MANUAL Bosch Electric Built-in Single & Double Oven Models HBN 64.J65,.166., BEFORE YOU BEGIN, READ THESE INSTRUCTIONS COMPLETELY AND CAREFULLY IMPORTANT: Save these instructions for _e local electrical inspector's nse'_ INSTALLER: Please leave this manual w_th owner for future reference.
-
Page 2: Table Of Contents
Table of Contents INTRODUCTION ..........................Tools You Will Need ........................Power Requirements ...... Choosing Oven Location ......................Steps for Installation ........................TECHNICAL DATA ........................[..Single oven ........................... Double oven ..........................UNDERCOUNTER INSTALLATION ..................SINGLE OVEN ..........................WALL INSTALLATION .................. -
Page 3: Introduction
INTRODUCTION •,aT208 volt circuit must be used, wiring inside oven must be modified. See Connection to a 208 Volt Circuit, in this manuai. A circui[ breaker Please read these instructions COMPLETELY time-delay fuse sized not to exceed the circuit rat- AND CAREFULLY. -
Page 4: Technical Data
Maximum Connected Load Convection Single Oven Models Oven Watts Volts Hertz Amperes @240V/208V @240V/208V 240/208 13.1/13.3 HBN 642A UC 3,150/2,775 240/208 13.1/13.3 HBN 645A UC 3,150/2,775 2401208 13.1/13.3 HBN 646A UC 3,150/2,775 DOUBLE OVEN For cutout dimensions sec following... -
Page 5: Undercounter Installation
UNDERCOUNTER INSTALLATION, SINGLE O_n elec_l_ supply: Locate Jun_onboxIn _lJa_mt cabinet o r below bottom support s urface. _" opening width Bottom supper sud_,e must be solid, le_i_ and able to supper at least of 150 Ibs. 114"min. distance b_'ween ovln door frme md -,,'jas*nt doom or dmw_ fron'= toe spa_... -
Page 6: Wall Installation
WALL INSTALLATION, SINGLE OVEN Secureoven to cabinet uSklgthe screws movlded. Screws should be Inserted .= Ihrough the mountln_ holes In _e posi_ora _ldicat_d in me frame (o_m ! doorto see flame and mounlJngho_es I . Donot ov_tighten screws. 6. Be careful when placing... -
Page 7: Double Oven
WALL INSTALLATION, DOUBLE OVEN Secure oven to cabinet using the screws provided. Screws should be inserted through mounting holes in the positions indicated in the frame (open door to see frame and mounting holes). Do not overtightan screws, Note: Do not slide oven across floor. -
Page 8: Wiring Requirements
WIRING REQUIREMENTS ELECTRICAL SUPPLY When making the wire connections, use the entire length of the conduit provided (3 fee0. The con- Before installing the oven have a qualified electri- duit must not be cut. cian verify that your home is provided with ade- Before making connections make sure the power quate electrical... -
Page 9: Connecting To 208 Volt Circuit
To connect to 208 volt circuit: CONNECTING TO 208 V CIRCUIT Remove the access panel(s) lQcated on the ovens are pre-wired for connection to 240 back of the oven(s). volt, 60 Hertz supply. If connecting to a 208 volt, Loosen the first and second screws in the ter- 60 Hz. -
Page 10: Electrical Connections
ELECTRICAL CONNECTIONS 3-WIRE BRANCH CIRCUIT Refer to Figure A, where local codes allow the connection of GROUND wire from the oven to This appliances is manufactured with a green GROUND wire connected to the oven chassis. the branch circuit NEUTRAL wire (grey or white colored wire): After making sure that the power has been turned off connect the flexible conduit from the oven to... -
Page 11: Final Checklist
FINAL CHECK LIST you have modified the oven(s) for use on 208 volt the voltage reading between the black and red wires should be 190 to 208 volts. To prevent improper connections leading to dam- Set the time of day by pressing the Set age of electrical components...