Advertisement
Quick Links
Download this manual
See also:
Use and Care Manual
BUILT BETTER THAN IT HAS TO BE"
Installation
Instructions
Top Loading
Washer
Keep instructions
for future
reference.
Be sure manual
stays with washer.
MOVE
WASHER
TO FINAL
AREA;
REMOVE
SHIPPING
BRACE
& PLUG
Protect the floor when moving the
washer. Washer must be within 4 feet
of desired area before beginning
installation. Open washer lid and
remove installation parts from
shipping brace for use.
Reach through foam shipping
brace, grasp bottom of brace, and
pull up to remove.
i
NOTE: Save shipping plug and
shipping brace; reinstall whenever
washer is moved more than 4 feet.
Do not lift or move washer without
shipping materials in place.
To remove the shipping plug from the
washer, step on the card board base,
tilt the washer back, and slide out the
base.
i
Cardboard
base
Shipping
brace
Shipping
plug
CONNECT
WATER
FILL
HOSES
TO
WASHER
Tightly push one flat rubber
washer into one end of each
water fill hose and attach this end
of hose to washer. HOT and
COLD connections are identified
by letters H and C stamped into
washer cabinet and by HOT and
COLD printed on water fill hoses.
In most cases, hoses should
cross when attached to correct
water temperature faucet.
]]ghten hose connections by hand
until snug, then another ¼ turn with
pliers. DO NOT cross-thread or over-
tighten couplings.
end of fill hose.
Advertisement
Related Manuals for Amana NAV3330AWW
Summary of Contents for Amana NAV3330AWW
- Page 1 BUILT BETTER THAN IT HAS TO BE" Installation Instructions Top Loading Washer Keep instructions for future reference. Be sure manual stays with washer. NOTE: Save shipping plug and Shipping MOVE WASHER shipping brace; reinstall whenever brace TO FINAL AREA; washer is moved more than 4 feet. REMOVE Do not lift or move washer without SHIPPING...
- Page 2 i¸¸ CONNECT Tightly push one screened filter ..,,,_.---, ...__ washer onto remaining end of each lflf,_ I "K rill. water fill hose. Attach water hoses to __ _ faucets HOSES HOT and COLD faucets. BE SURE JJHOT ,_ _ FAUCETS HOT WATER HOSE IS CONNECTED __J _._K ..
-
Page 3: Level Washer
WASHER MUST NOT ROCK. _,.._ /1 ff ..} Questions? CONNECT POWER CORD See Owner's Manual or call ELECTRICITY Amana Consumer Affairs I'r ")' CLEAN Wipe tub with clean rag and soap I_IIIM Tl-II_rllllt':.l.I dilutedinwarmwatertoremove ....any oil used in manufacturing. | Department... -
Page 4: Installation
Installation Summary water CotM'lect frillhoses to faucets Connect water cycle before fill hoses to washing clothes Set to 140°F washer Run through Connect power electricity cord to Secure drain hose Level front and rear legs Tools Parts Supplied (in shipping brace) 4 rubber leveling Screwdriver... -
Page 5: Safety Information
DO NOT pinch power cord. Optional Kits Washer Dimensions Kits are available at extra cost through Amana dealer or Amana factory 1-800-843-0304. Siphon Break Kit For standpipe installation below 36" 53.5" (91.44 cm), install part #562P3. (137.1cm) Longer Water Inlet Hoses 8' (2.44 m) inlet hose, part #20617. - Page 6 Drain receptacle must be able to handle hose with at least 1¼" (32cm) outside diameter. End of drain hose must be 36" (91.44 cm) above floor, or water may run out of washer before end of cycle. Part No. 40085801 © 1999 Amana Appliances printed in U.S.A. 8/99 Amana, Iowa 52204...