Table of Contents
Advertisement
TRENDnet User's Guide
configured automatically. Stateless DHCPv6: A stateless DHCP server will only
provide configuration information to the nodes and will rely on ICMPv6
(Internet Control Message Protocol version 6) router discovery messages to
assign IPv6 addresses. DHCPv6 (Stateful): Dynamic Host Configuration
Protocol for IPv6. Stateless address autoconfiguration for IPv6 can be used to
acquire access in an IPv6 network, however, it is generally recommended to
use DHCPv6 instead to assign addresses, name servers and other configuration
information to the clients.
• DHCPv6 (Stateful): TEW-691GR WAN port use DHCPv6 client to obtain IP addresses
and other configuration information from stateful DHCPv6 server. Dynamic state
information about each individual client is stored and centrally managed on the
DHCPv6 server.
o Manually configure DNS: When enabled, users will be given the options to
manually enter DNS servers
o Primary DNS Server: Your local ISP will assign this address to you
o Secondary DNS Server: Your local ISP will assign this address to you
o Enable DHCP-PD: Enable the DHCP Prefix Delegation which is used to assign
a network address prefix to a user site, configuring the user's router with the
prefix to be used for each LAN. This is one of the methods for delegating IPv6
address prefixes to an IPv6 subscriber's network (or "site").
o LAN IPv6 Address: Please enter the IPv6 Address here
o LAN Prefix Length: LAN Prefix Length will be displayed here
o LAN IPv6 Link-Local Address: IPv6 Link-Local Address will be displayed here
o Autoconfiguration Type: Set up IPv6 Autoconfiguration in this section in order to
have IPv6 addresses assigned to the clients on the local area network. The
options are Stateless Auto, Stateless DHCPv6, DHCPv6 (Stateful). Stateless Auto:
When connected to an IPv6 network utilizing ICMPv6 (Internet Control Message
Protocol version 6) router discovery messages, IPv6 hosts will be configured
automatically. Stateless DHCPv6: A stateless DHCP server will only provide
configuration information to the nodes and will rely on ICMPv6 (Internet Control
Message Protocol version 6) router discovery messages to assign IPv6 addresses.
DHCPv6(Stateful): Dynamic Host Configuration Protocol for IPv6. Stateless
address autoconfiguration for IPv6 can be used to acquire access in an IPv6
network, however, it is generally recommended to use DHCPv6 instead to assign
addresses, name servers and other configuration information to the clients.
© Copyright 2012 TRENDnet. All Rights Reserved.
• Link-Local: The Link-local address is used by nodes and routers when
communicating with neighboring nodes on the same link. This mode enables IPv6-
capable devices to communicate with each other on the LAN side.
o LAN IPv6 Address: Please enter the IPv6 Address here
o LAN IPv6 Link-Local Address: IPv6 Link-Local Address will be displayed here
• PPPoE: Select this option if your ISP requires you to use a PPPoE (Point to Point
Protocol over Ethernet) connection to IPv6 Internet. DSL providers typically use this
option. This method of connection requires you to enter a Username and Password
(provided by your Internet Service Provider) to gain access to the IPv6 Internet.
o PPPoE session: The options are Shared with IPv4 or Create New Session. You can
select to share IPv6 with IPv4 within a single PPPoE session or to create a
seperate PPPoE session for IPv6 instead.
o User Name: Please consult with your ISP for your login account information
o Password: Please consult with your ISP for your login account information
o Verify Password: Please enter your password again to verify it is correct
o Address Mode: Please select Auto or Static. Address Mode (Auto): Select this
option if the ISP's servers assign the router's WAN IPv6 address upon establishing
a connection. Address Mode (Static): Select this option if your ISP has assigned a
fixed IPv6 address. The ISP will provide the value for the IPv6 Address and Subnet
Prefix Length.
o Use Default MTU Setting: It is recommended to use the default MTU setting.
o MTU Setting: Enter your MTU setting here when Default MTU Setting is disabled
o Manually configure DNS: When enabled, users will be given the options to
manually enter DNS servers
o Primary DNS Server: Your local ISP will assign this address to you
o Secondary DNS Server: Your local ISP will assign this address to you
o Enable DHCP-PD: Normally this option is enabled in PPPoE mode. When enabled,
this router will use ISP-provided IPv6 address prefix to configure this router's LAN
port global IPv6 address and provide global address pool to LAN side PC when
either stateless DHCPv6 or stateless Auto is enabled.
o LAN IPv6 Address: Please enter the IPv6 Address here
o LAN Prefix Length: LAN Prefix Length will be displayed here
o LAN IPv6 Link-Local Address: IPv6 Link-Local Address will be displayed here
TEW-691GR
30
Advertisement
Table of Contents
