CPU, and later add another, when more processing power is required. Remember to take a look at Tyan Computers web site located at http://www.tyan.com. Here you can find information on all of Tyan's products along with FAQ's, distributors list, drivers and CMOS setting explanations.
EIDE Mode 0 through Mode 4 drives Supports DMA(Bus Master) mode 1 and 2. ( Bus Master driver on web at www.tyan.com) wEnhanced I/O Multi-mode bi-directional parallel port that supports standard, EPP and ECP modes.
Award BIOS/Flash are trademarks of Award Software International Inc. AMI BIOS is a trademarks of American Megatrends Inc. IBM,PC,AT,PS/2 are trademarks of IBM Corporation INTEL,Pentium Pro are trademarks of Intel Corporation. Copyright c 1996 TYAN Computer Corp. S1662, Titan Pro AT. S1662-AT-001 http://www.tyan.com...
2.2 Installation You are now ready to install your mainboard. The mounting hole pattern of the S1662 matches the "Baby AT" system board spec. It is assumed that the chassis is for a standard IBM XT/AT form factor. S1662-AT-001 http://www.tyan.com...
DRAM Voltage: J20, J21, J22, J23, J44, J45, J47,and J48. Default is 5V(Some EDO memory is 3.3V) Voltage J20 J21 J22 J23 J44 J45 J47 J48 3.3V off off off off off on on Warning, damage to system can result if set incorrectly! S1662-AT-001 http://www.tyan.com...
Page 9
Keylock Ground Turbo Switch: J30 ( Non-Turbo Mode Not Supported ) HDD LED: J43 Pinout Assignments Cathode Anode Cathode Anode Pins 1 and 2 are for primary IDE channel. Pins 3 and 4 are for secondary IDE channel. S1662-AT-001 http://www.tyan.com...
Page 10
Signal In Gound Signal Out Super I/O Type: J34 Type 665IR 669IR This setting depends on what type of SMC I/O chip is installed on the board. This jumper is set at the factory and should not be changed. S1662-AT-001 http://www.tyan.com...
(J30) for the cable that may come with the case. 3.6 Turbo LED Connector Installation The TURBO LED on the front case panel can indicate the current speed status of the system. The TURBO LED connector should be installed to J29 in the correct direction. S1662-AT-001 http://www.tyan.com...
Short jumper J5. c. Wait for 5 seconds then remove the jumper from J5. d.Then power on the system again. By doing the above procedures, your password will be erased and the CMOS will be reset to the BIOS defaults. S1662-AT-001 http://www.tyan.com...
CPU in the socket. This is normal and will not damage the CPU. When the CPU is installed, the lever should snap into place at the side of the socket in the down position.. S1662-AT-001 http://www.tyan.com...
If a PCI-Bus interface card is to be installed in the system, any one of the five PCI-Bus slots can support either a Master or a Slave device. After installing the peripheral controllers, the user should check everything again, and prepare to power-on the system. S1662-AT-001 http://www.tyan.com...
Orient the connectors so the black wires are in the middle of the 5V power supply. Caution: Some power supplies also include "3V" connectors. The connection wires normally have two colors with 3 black wires on one side. Please be very careful. Don't to use the wrong connec- tor. S1662-AT-001 http://www.tyan.com...
Page 18
You may need to hold the lead at an angle to line it up.Once you have the guide pins aligned, press the lead connector so that the plastic clips on the lead snap into place and secure the lead to the connec- tor. Connecting 5V power supply S1662-AT-001 http://www.tyan.com...
Figure 4.1 will appear on the sceen. The Main Menu allows you to select from the 8 setup functions and 2 exit choices. Use the arrow keys to select among the items and press <Enter> to accept or enter each sub-menu. S1662-AT-001 http://www.tyan.com...
Calendar, only for Status Page Setup Menu F4 key Reserved F5 key Restore the previous CMOS value, only for Option Page Setup Menu F6 key Load defaults F8 key Reserved F9 key Reserved F10 key Save all CMOS changes, only for Main Menu S1662-AT-001 http://www.tyan.com...
USER PASSWORD POWER MANAGEMENT IDE HDD AUTO DETECT PNP/PCI CONFIGURATION SAVE AND EXIT LOAD BIOS DEFAULTS EXIT WITHOUT SAVING ESC : Save & Exit Setup :Select Item F10 : Quit (Shift)F2 :Change Color Time, Date, Hard Disk Type,..S1662-AT-001 http://www.tyan.com...
Page 22
I/O options. w w IDE HDD auto detection Automatically configure hard disk parameters. w w Save and exit setup Save changes to CMOS and exit setup w w Exit without saving Abandon all CMOS changes and exit setup. S1662-AT-001 http://www.tyan.com...
The day, from Sun to Sat, Determined by the BIOS date, month and year entries. Date The date, from 1 to 31 (or maximum allowed in a month) Month The month, Jan to Dec. Year The year, from 1900 to 2099 S1662-AT-001 http://www.tyan.com...
Page 24
1.2M,5.25 5-1/4 inch AT-type high-density drive; 1.2 megabyte capacity 720K, 3.5 in. 3-1/2 inch double-sided drive; kilobyte capacity 1.44M, 3.5 in. 3-1/2 inch double-sided drive; 1.44 megabyte capacity 2.88M, 3.5 in. 3-1/2 inch double-sided drive; 2.88 megabyte capacity S1662-AT-001 http://www.tyan.com...
Page 25
The value of the base memory is typically 640K. Extended Memory The BIOS determines how much extended memory is present during the POST. This is the amount of memory located above 1MB in the CPU's memory address map. S1662-AT-001 http://www.tyan.com...
Page 27
Swap Floppy Drive Default value is Disabled E n a b l e d Floppy A & B will be swapped under DOS D i s a b l e Floppy A & B will be normal definition. S1662-AT-001 http://www.tyan.com...
Page 28
The selected character is displayed when a key is held down after a delay set by the Typematic Rate Delay. It then repeats at a rate set by the Typematic Rate. S1662-AT-001 http://www.tyan.com...
:Enable DRAM Read Burst(B/E/F) :x1/2/3 DRAM Write Burst(B/E/F) :x2/2/3 More Information on these settings ISA Bus Clock :PCICLK/4 can be found at Tyan's web site. DRAM Refresh Queue :Disable http://www.tyan.com DRAM RAS# Only Refresh :Disable ECC Checking/Generation :Disable Fast DRAM Refresh...
Video Off Method The "Blank Screen" option will let the system BIOS blanks the screen when disabling video. V/H SYNC+Blank will let the BIOS turn off the V-SYNC and H-SYNC signals from the VGA card to the monitor. S1662-AT-001 http://www.tyan.com...
Page 31
Standby Mode Defines the continous idle time before the system enters Standby mode. w w Power Down Activities Defines the the activities that can cause the PM timers to reload. (Break- ing out of PM Mode) S1662-AT-001 http://www.tyan.com...
Page 33
Primary IDE INT# Select the PCI INT# that the Primary IDE controller will use. Default value is A. w w Secondary IDE INT# Select the PCI INT# that the Secondary IDE controller will use. Default value is B S1662-AT-001 http://www.tyan.com...
On-Board Parallel Port :378/IRQ7 Parallel Port Mode :Normal The Settings in the Integrated Peripherals lets the user enable or disable on-board device. You can also configure the I/O and IRQ settings of the on-board serial and parallel ports. S1662-AT-001 http://www.tyan.com...
If any problem has occurred, loading the SETUP DEFAULTS is recommended. 4.10. PASSWORD SETTING When you select this function, the following message will appear at the center of the screen to assist you in creating a password. ENTER PASSWORD S1662-AT-001 http://www.tyan.com...
Page 36
If you select Setup at Security Option of BIOS Features Setup Menu, you will be prompted only when you try to enter setup. S1662-AT-001 http://www.tyan.com...
ESC : Save & Exit Setup :Select Item F10 : Quit (Shift)F2 :Change Color Type "Y" and you will quit the Setup Utility and save the user setup values to RTC CMOS SRAM. Type "N" to return to Setup Utility. S1662-AT-001 http://www.tyan.com...
You cannot upgrade an Award BIOS to a AMI BIOS or a AMI BIOS to an Award BIOS. *This file name is subject to change and can have either a "bin" or a "rom" extension. S1662-AT-001 http://www.tyan.com...
Page 39
If you are not sure, try running FMW. If it runs, then you have suc- ceeded. If it displays a warning message about the CPU mode, you will have to try again. S1662-AT-001 http://www.tyan.com...
Mainboard, your system may not be able to boot. If this happens, it will require service by your system vendor. Follow the requirements and instructions in this section precisely to aviod inconvenience. S1662-AT-001 http://www.tyan.com...
3 SERIAL port 2 4 SERIAL port 1 5 PARALLEL port 2 6 FLOPPY DISK adapter 7 PARALLEL port 1 8 RTC clock 9 Available 10 Available 11 Available 12 PS/2 Mouse 13 MATH co-processor 14 Primary IDE 15 Secondary IDE S1662-AT-001 http://www.tyan.com...