Related Manuals for Zenoah CHT2310
Summary of Contents for Zenoah CHT2310
- Page 1 HT2310 CHT2310 848D0593A0 (706) OWNER’S MANUAL HEDGE TRIMMER HT2310 / CHT2310 GB-1...
- Page 2 HT2310 / CHT2310 EXPLANATION OF SYMBOLS AND SAFETY WARNINGS HT2310 CHT2310 MODEL HTZ2310 22.5 cm CHTZ2310 22.5 cm APPROVAL NUMBER OF CE EXHAUST EMISSION REGULATION GB-2 WARNING!!! RISK OF DAMAGING HEARING Wear head, eye and ear protection. WARNING!!! RISK OF DAMAGING HEARING Wear head, eye and ear protection.
-
Page 3: Table Of Contents
EC DECLARATION OF CONFORMITY ZENOAH CO., LTD. 1-9, Minamidai, Kawagoe, Saitama, Japan DIRECTIVE 89/336/EEC, 98/37/EC 2000/14/EC Internal control production. : HEDGE TRIMMER : HT2310 CHT2310 : 70300001 and up Specification sheet Inspection standard 1st March 2007 Contents 1. Parts location ... 4 2. -
Page 4: Parts Location
12. Plate receive 2. Specification Model ... HT2310 / CHT2310 Type ... double-action type HT2310 / CHT2310 ... Single blade / Double blade Blade length (from the tip of Gear Case) HT2310 / CHT2310 ... 750 / 600 mm Engine Model ... -
Page 5: Warning Labels On The Machine
Position: AIR CLEANER COVER The direction to open the choke Position: AIR CLEANER COVER HT2310 / CHT2310 If warning label peels off or becomes soiled and impossible to read, you should contact the dealer from which you purchased the product to order new labels and affix them in the required location(s). -
Page 6: For Safe Operation
HT2310 / CHT2310 5. For safe operation 1. THIS MACHINE CAN CAUSE SERIOUS INJURIES. Read this manual carefully until you com- pletely understand and follow all safety and operating instruc- tions. Also, know how to stop the machine quickly in an emer- gency. - Page 7 HT2310 / CHT2310 WARNING Never place the throttle into the high-speed position when starting the engine.
- Page 8 HANDLING FUEL 1. The engine of the ZENOAH prod- uct is designed to run on a mixed fuel, which contains highly flam- mable gasoline. Never store cans...
-
Page 9: Fuel
• The Zenoah engines are lubricated by oil specially formulated for air-cooled 2-cycle gasoline engine use. If Zenoah oil is not available, use an anti-oxidant added quality oil expressly labeled for air-cooled 2-cycle engine use (JASO FC GRADE OIL or ISO EGC GRADE). -
Page 10: Operation
HT2310 / CHT2310 7. Operation STARTING ENGINE WARNING The cutting head will start moving upon the engine starts. 1. Release the throttle lever and make sure it is fully back. 2. Set the ignition switch to the “I” position. [HT2310]... - Page 11 Do not allow anyone to stay close to the hedge- trimmer while working or while adjusting the car- buretor. HOW TO USE : HANDLE (CHT2310) • To reduce fatigue when trimming hedges, the handle can be swivelled through 45° or 90° to the left or right.
-
Page 12: Maintenance
HT2310 / CHT2310 8. Maintenance System/components fuel leaks, fuel spillage fuel tank, air filter, fuel filter idle adjusting screw spark plug cylinder fins, intake air cooling vent muffler, spark arrester, cylinder exhaust port throttle lever, ignition switch cutting parts gear case... - Page 13 14.7–21.5 N·m TIGHTENING TORQUE: GEAR CASE ･ Supply multi-purpose grease at every 25 hours of use. 1. Use a grease pump. Feed grease until it comes out of the base of blades(a). HT2310 / CHT2310 GB-13...
-
Page 14: Storage
HT2310 / CHT2310 8. Maintenance PROCEDURES TO BE PERFORMED AF- TER EVERY 100 HOURS OF USE 1. Remove the muffler, insert a screwdriver into the vent, and wipe away any carbon buildup. Wipe away any carbon buildup on the muffler exhaust vent and cylin- der exhaust port at the same time. -
Page 15: Troubleshooting Guide
(exhaust port) Æ carbon is built-up air cleaner cylinder fin, fan cover When your unit seems to need further service, please consult with our ZENOAH service shop in your area. Limited warranty Should any failure occur on the product under normal...