The 10 Second T The 10 Second Tutor Utor - SoundCraft COMPACT 4 User Manual

THE 10 SECOND TUTOR - COMP THE 10 SECOND TUTOR - COMP
THE 10 SECOND TUTOR - COMPACT4 / COMP THE 10 SECOND TUTOR - COMP THE 10 SECOND TUTOR - COMP
1
MIC INPUT MIC INPUT MIC INPUT
MIC INPUT MIC INPUT
2
LINE INPUT LINE INPUT LINE INPUT
LINE INPUT LINE INPUT
3
HIGH PASS FILTER HIGH PASS FILTER HIGH PASS FILTER
HIGH PASS FILTER HIGH PASS FILTER
4
INSERT POINT INSERT POINT INSERT POINT INSERT POINT INSERT POINT
5
GAIN CONTROL GAIN CONTROL
GAIN CONTROL GAIN CONTROL GAIN CONTROL
678
EQ STAGE EQ STAGE
EQ STAGE EQ STAGE EQ STAGE
9
PAN CONTROL PAN CONTROL PAN CONTROL PAN CONTROL PAN CONTROL
0
INPUT CHANNEL LEVEL INPUT CHANNEL LEVEL INPUT CHANNEL LEVEL INPUT CHANNEL LEVEL INPUT CHANNEL LEVEL
q
REC(ORD) SWITCH REC(ORD) SWITCH REC(ORD) SWITCH REC(ORD) SWITCH REC(ORD) SWITCH
w
MONITOR SWITCH MONITOR SWITCH MONITOR SWITCH
MONITOR SWITCH MONITOR SWITCH
e
PHANTOM POWER PHANTOM POWER PHANTOM POWER
PHANTOM POWER PHANTOM POWER
r
D.I. SWITCH D.I. SWITCH D.I. SWITCH D.I. SWITCH D.I. SWITCH
t
R.I.A.A. SWITCH R.I.A.A. SWITCH
R.I.A.A. SWITCH R.I.A.A. SWITCH R.I.A.A. SWITCH
y
STEREO INPUTS STEREO INPUTS STEREO INPUTS
STEREO INPUTS STEREO INPUTS
ui
PLAYBACK INPUTS PLAYBACK INPUTS PLAYBACK INPUTS
PLAYBACK INPUTS PLAYBACK INPUTS
op
RECORD OUTPUTS RECORD OUTPUTS RECORD OUTPUTS RECORD OUTPUTS RECORD OUTPUTS
a
MONITOR OUTPUTS MONITOR OUTPUTS
MONITOR OUTPUTS MONITOR OUTPUTS MONITOR OUTPUTS
s
MIX OUTPUTS MIX OUTPUTS
MIX OUTPUTS MIX OUTPUTS MIX OUTPUTS
d
MONITOR LEVEL MONITOR LEVEL MONITOR LEVEL MONITOR LEVEL MONITOR LEVEL
f
MIX LEVEL MIX LEVEL MIX LEVEL MIX LEVEL MIX LEVEL
g
MONO (CHK) SWITCH MONO (CHK) SWITCH MONO (CHK) SWITCH MONO (CHK) SWITCH MONO (CHK) SWITCH
h
MONITOR MIX MONITOR MIX MONITOR MIX
MONITOR MIX MONITOR MIX
j
RECORD LEVEL RECORD LEVEL RECORD LEVEL RECORD LEVEL RECORD LEVEL
k
PLAYBACK LEVEL PLAYBACK LEVEL PLAYBACK LEVEL PLAYBACK LEVEL PLAYBACK LEVEL
l
MAIN METERS MAIN METERS
MAIN METERS MAIN METERS MAIN METERS
;
MONITOR PLAYBACK MONITOR PLAYBACK MONITOR PLAYBACK
MONITOR PLAYBACK MONITOR PLAYBACK
z
POWER / LOW BAT. POWER / LOW BAT. POWER / LOW BAT.
POWER / LOW BAT. POWER / LOW BAT.
x
ARTIST MIX ARTIST MIX ARTIST MIX ARTIST MIX ARTIST MIX
c
ARTIST LEVEL ARTIST LEVEL ARTIST LEVEL ARTIST LEVEL ARTIST LEVEL
v
ARTIST HEADPHONES ARTIST HEADPHONES
ARTIST HEADPHONES ARTIST HEADPHONES ARTIST HEADPHONES
b
ENGINEER LEVEL ENGINEER LEVEL ENGINEER LEVEL ENGINEER LEVEL ENGINEER LEVEL
n
ENGINEER HEADPHONES ENGINEER HEADPHONES ENGINEER HEADPHONES ENGINEER HEADPHONES ENGINEER HEADPHONES
m
MONITORS/ARTIST MIX MONITORS/ARTIST MIX MONITORS/ARTIST MIX MONITORS/ARTIST MIX MONITORS/ARTIST MIX
USER GUIDE USER GUIDE USER GUIDE
USER GUIDE USER GUIDE
ACT4 / COMP ACT4 / COMP
ACT4 / COMP ACT4 / COMPACT 10
Connect Microphones here - read phantom power notes before use (pg 22)
Connect Line level sources here, e.g. Synth, Drum Machine, etc (pg 22)
This is used to remove very low frequencies i.e. mic "popping" (pg 22)
Connect Signal processors here, e.g. Compressor, Gate etc (pg 23)
Adjust this to increase or decrease the level of the incoming signal (pg 23)
Adjust these controls to change the signal tone (the character of the signal) (pg 23)
Use this control to position the signal within the stereo field (pg 24)
This is used to control the level fed to the Mix Bus (pg 24)
This sends the channel being recorded to the record outputs, or the Mix Bus (pg 24)
Press this to listen to the associated signal (pg 24)
Switches on the phantom power (48V) for condenser microphones (pg 22)
WARNING: WARNING:
WARNING: WARNING: Do Not apply Phantom Power before connecting a microphone WARNING:
Direct Injection - Press this to get a better signal match when a bass guitar is used (pg 23)
Vinyl Record Deck Compensation - Use only when decks are connected (pg 25)
These two inputs take audio from keyboards, sound modules, samplers etc (pg 25)
Here you can connect the playback from your soundcard or recording device (pg 28)
To connect the output from the mixer to your soundcard (or recording device) input (pg 28)
These are used to feed your speakers / amp, or monitoring system (pg 26)
Connect these to your recording device, or to your amplification system when using as a
standard mixer, not when using with a computer based system (pg 26)
Used to adjust the level sent to your speakers / amp, or monitoring system (pg 26)
Used to adjust the level sent from the mix outputs (pg 26)
Use this to hear and check to your mix in mono (pg 26)
Use this to listen to the mix outputs (pg 26)
Used to adjust the level sent to your soundcard or recording device (pg 28)
Used to adjust the level coming from your soundcard or recording device (pg 28)
These show the level of the signal being monitored (pg 26)
Use this to listen to the playback signal from your soundcard (pg 28)
Indicators for DC power from the adapter, or the battery pack (pg 26)
This lets the artist choose the amount of playback signal required (pg 27)
This controls the level of the signal sent to the artist's headphones (pg 27)
The artist should plug headphones in here for personal monitoring (pg 27)
This controls the level of the signal sent to the engineer's headphones (pg 27)
The engineer should plug headphones in here for standard monitoring (pg 27)
The engineer, using headphones can listen to the monitor signal or the artist mix (pg 27)
ACT 10 ACT 10
ACT 10 ACT 10
11