Page 2
Acknowledgments AMI is a registered trademark of American Megatrends Inc. PS/2 is a trademark of International Business Machines Corporation. Intel and Intel® Arrandale DC Mobile Processor are registered trademarks of Intel Corporation. Microsoft Windows is a registered trademark of Microsoft Corporation.
Board Dimensions ............... 4 Installations ............6 Installing the CPU ............... 7 Installing the Memory ............8 Setting the Jumpers ............. 9 Connectors on 2808220 ............13 BIOS Setup ............23 Drivers Installation ........51 Intel Chipset Software Installation Utility......52 VGA Drivers Installation ..........
Page 4
IMPORTANT NOTE: When the system boots without the CRT being connected, there will be no image on screen when you insert the CRT/VGA cable. To show the image on screen, the hotkey must be pressed (CTRL-ALT-F1). 2808220 User’s Manual...
INTRODUCTION Introduction Product Description The 2808220 Mini ITX board incorporates the Intel® Chipset for Embedded Computing, consisting of the Intel® Arrandale DC mobile processor (integrated Graphic and Memory Controller) and Intel® Ibex Peak-M (PCH), an optimized integrated graphics solution with a 800/1066MHz front-side bus. Dimensions of the board are 170mm x 170mm.
INTRODUCTION Checklist Your 2808220 package should include the items listed below. • The 2808220 Mini-ITX motherboard • This User’s Manual • 1 CD containing chipset drivers and flash memory utility • Cable kit (Serial port, Serial ATA) 2808220 User’s Manual...
4-pin header x1 for CD in, SPDIF-out connector x1 SATA connector x4 for SATA ports Watchdog Timer Yes (256 segments, 0, 1, 2…255 sec/min) System Voltage +5V, +3.3V, +12V, -12V, 5VSB (2A) Others Modem Wakeup, LAN Wakeup 170mm x 170mm (Mini ITX) Board Size 2808220 User’s Manual...
INSTALLATIONS Installations This section provides information on how to use the jumpers and connectors on the 2808220 in order to set up a workable system. The topics covered are: Installing the CPU .................. 7 Installing the Memory ................8 Setting the Jumpers ................9 Connectors on 2808220 ................
INSTALLATIONS Installing the CPU The 2808220 board supports rPGA989 socket for Intel® Arrandale Dual Core mobile processors. The processor socket comes with a screw to secure the processor. As shown in the left picture below, loosen the screw first before inserting the processor.
INSTALLATIONS Installing the Memory The 2808220 board supports two DDR3 memory socket for a maximum total memory of 8GB in DDR3 SO-DIMM memory type. Installing and Removing Memory Modules To install the DDR3 modules, locate the memory slot on the board and perform the following steps: 1.
INSTALLATIONS Setting the Jumpers Jumpers are used on 2808220 to select various settings and features according to your needs and applications. Contact your supplier if you have doubts about the best configuration for your needs. The following lists the connectors on 2808220 and their respective functions.
SHIELD 0/5 DATA 4+ DATA 5- DDC CLOCK DATA 5+ DDC DATA SHIELD CLK CLOCK - DATA 1- CLOCK + DATA 1+ SHIELD 1/3 DATA 3- DATA 3+ DDC POWER A GROUND2 A GROUND 1 A GROUND3 2808220 User’s Manual...
Pin # Signal Name Green Blue N.C. N.C. N.C. DDC DATA HSYNC VSYNC DDC_CLK CN4: PS/2 Keyboard/Mouse Connectors and USB5/6 Ports PS/2 Keyboard & Mouse USB Port5 /Port6 Signal Name Keyboard/Mouse Keyboard data Mouse data Keyboard clock Mouse clock 2808220 User’s Manual...
INSTALLATIONS USB_LAN1: 10/100/1000 RJ-45 (2808220F) and USB3/4 Ports USB_LAN2: 10/100/1000 RJ-45 (2808220) and USB1/2 Ports CN5: Audio Connector The audio connector, from top to bottom, is composed of Line in, Line out and Microphone jacks. COM3_COM4: COM3, COM4 Serial Port...
ATX Power On Switch Not Defined Power LED Speaker Speaker: Pins 1 - 4 This connector provides an interface to a speaker for audio tone generation. An 8-ohm speaker is recommended. Pin # Signal Name Speaker out No connect Ground 2808220 User’s Manual...
Page 23
Hard Disk Drive LED Connector: Pins 10 and 20 This connector connects to the hard drive activity LED on control panel. This LED will flash when the HDD is being accessed. Pin # Signal Name HDD Active 2808220 User’s Manual...
Pin # Signal Name DCD, Data carrier detect DSR, Data set ready RXD, Receive data RTS, Request to send TXD, Transmit data CTS, Clear to send DTR, Data terminal ready RI, Ring indicator GND, ground Not Used 2808220 User’s Manual...
Pin # Signal Name +12V Backlight Enable Brightness Control Ground J3: Digital I/O Signal Name Signal Name OUT3 OUT1 OUT2 OUT0 J4: CD-In Pin Header Pin # Signal Name CD Audio R Ground Ground CD Audio L 2808220 User’s Manual...
MIC2 L Ground MIC2_R Presence# Line2 L MIC2 ID Sense Line2 R Line2 ID J7: PCI-E(x1) Slot J8: SPDIF Out Connector PCI1: PCI Slot (supports 2 Master) JMINI: Mini PCIE Connector SATA1, SATA2, SATA3, SATA4: SATA Connectors 2808220 User’s Manual...
<PgUp> and <PgDn> keys to change entries, <F1> for help and <Esc> to quit. When you enter the Setup utility, the Main Menu screen will appear on the screen. The Main Menu allows you to select from various setup functions and exit choices. 2808220 User’s Manual...
System Language Choose the system default language. System Date Set the Date. Use Tab to switch between Data elements. System Time Set the Time. Use Tab to switch between Data elements. 2808220 User’s Manual...
Disabling TDT Allow user to login to platform. This is strictly for testing only. This does not disable TDT Services in ME. ► Intelligent Power Sharing Intelligent Power Sharing configuration menu. NOTE: DTS must be enabled for Power Sharing to function. ► MXM 3.0/Hybrid Graphics Enable/Disable the MXM 3.0 support.. 2808220 User’s Manual...
ASPM Support Set the ASPM Level: Force L0 – Force all links to L0 State AUTO – BIOS auto configure DISABLE – Disables ASPM Extended Synch If ENABLED allows generation of Extended Synchronization patterns. 2808220 User’s Manual...
Enter: Select NO TPM Hardware Change Field F1: General Help F2: Previous Values F3: Optimized Default F4: Save ESC: Exit TPM Support Enables or Disables TPM support. O.S. will not show TPM. Reset of platform is required. 2808220 User’s Manual...
Enables or Disables System wake on alarm event. When enabled, System will wake on the hr: min:: sec specified. Wake on Ring The options are Disabled and Enabled. Wake on PME The options are Disabled and Enabled. 2808220 User’s Manual...
XD can prevent certain classes of malicious buffer overflow attacks when combined with a supporting OS (Windows Server 2003 SP1, Windows XP SP2, SuSE Linux 9.2, Re33dHat Enterprise 3 Update 3.) Hardware Prefetcher To turn on/off the MLC streamer prefetcher. 2808220 User’s Manual...
ME SMBus Thermal Reporting Enable/Disable ME SMBus Thermal Reporting Configuration. PPEC Processor Power Error Correction. Processor Temperature Limit. MMGPC Max Memory Power Clamp. MPPC Max Processor Power Clamp. MPCP Max Processor Core Power Clamp. PCH Temperature Adjust. 2808220 User’s Manual...
Page 38
MCH Temperature Read Enable. PCH Temp Read PCH Temperature Read Enable. CPU Energy Read CPU Energy Read Enable. CPU Temp Read CPU Temperature Read Enable. Thermal Data Reporting Thermal Data Reporting Enable. Alert Enable Lock Lock all Alert Enable settings. 2808220 User’s Manual...
Options are Auto, Force Scaling, Off and Maintain Aspect Ratio. Backlight Control Back Light Control Setting. Options are PWM Inverted, PWM Nrmal, GMBus Inverted and GMBus Normal. BIA Control Options are VBIOS Default, Disabled and Level 1/2/3/4/5. 2808220 User’s Manual...
↑↓ Select Item Enter: Select Change Field F1: General Help F2: Previous Values F3: Optimized Default F4: Save ESC: Exit Enable/Disable TDT in BIOS for testing only. TDT Recovery Set the number of times Recovery attempted will be allowed. 2808220 User’s Manual...
Enabled/Disabled. This is a workaround for Oses without EHCI hand-off support. The EHCI ownership change should be claimed by EHCI driver. Device Reset Timeout USB mass storage device Start Unit command timeout. Options are: 10 sec / 20 sec / 30 sec / 40 sec. 2808220 User’s Manual...
Serial Port Configuration Set Parameters of Serial Ports. User can Enable/Disable the serial port and Select an optimal settings for the Super IO Device. Power Failure Options are: Keep last state Bypass mode Always on Always off (default) 2808220 User’s Manual...
Page 43
PC health status. Fan1/Fan2 Smart Fan Control This field enables or disables the smart fan feature. At a certain temperature, the fan starts turning. Once the temperature drops to a certain level, it stops turning again. 2808220 User’s Manual...
F3: Optimized Default Parity None F4: Save ESC: Exit Stop Bits Terminal Type VT-UTF8 Console Redirection Console Redirection Enable/Disable. Terminal Type VT-UTF8 is the preferred terminal type for out-of-band management. The next best choice is VT100+ and then VT100. 2808220 User’s Manual...
Launches (Enabled/Disabled) the boot option for legacy network devices. ME Subsystem Launches (Enabled/Disabled) the boot option for legacy network devices. End of Post Message Launches (Enabled/Disabled) the boot option for legacy network devices. Execute ME8x Launches (Enabled/Disabled) the boot option for legacy network devices. 2808220 User’s Manual...
By default, this item is disabled. Enable Compatible Revision ID. North Bridge This item shows the North Bridge Parameters. South Bridge This item shows the South Bridge Parameters. ME Subsystem This item shows the ME Subsystem Parameters. 2808220 User’s Manual...
Page 47
Select which graphics controller to use as the primary boot device. Options are IGD, PCI/IGD, PCI/PEG, PEG/IGD, PEG/PCI and SG. Graphics Turbo IMON Current Graphics turbo IMON current values supported (14-31). VT-d VT-d Enable/Disable. PCI Express Compliance Mode PCI Express Compliance Mode Enable/Disable. 2808220 User’s Manual...
Page 48
IGD Share Memory Size. Options are Disable, 32M, 64M and 128M. PAVP Mode Select PAVP Mode used by Internal Graphics Device. Options are Disabled and Enabled. PEG Force Gen1 PCI Express Port Force Gen1. Options are Disabled and 2808220 User’s Manual...
Select a minimum assertion width of the SLP_S4# signal. Audio Configuration The Audio Configuration settings Enable/Disable the Azalia HD Audio and the Azalia internal HDMI codec. High Precision Event Timer Configuration Enable/or Disable the High Precision Event Timer. 2808220 User’s Manual...
Enabled USB Port 5 Enabled USB Port 6 Enabled USB Port 7 Enabled USB Port 8 Enabled USB Port 9 Enabled USB Port 10 Enabled USB Port 11 Enabled USB Port 12 Enabled USB Port 13 Enabled 2808220 User’s Manual...
ALWAYS – do not allow disabling GA20; this option is useful when any RT code is executed above 1MB. Option ROM Messages Set display mode for Option ROM. Options are Force BIOS and Keep Current. Interrupt 19 Canture Enable: Allows Option ROMs to trap Int 19. 2808220 User’s Manual...
Setup. In Setup the User will have Change Field Administrator rights F1: General Help F2: Previous Values Administrator Password F3: Optimized Default User Password F4: Save ESC: Exit Administrator Password Set Setup Administrator Password. User Password Set User Password. 2808220 User’s Manual...
Reset system setup without saving any changes. Save Changes Save Changes done so far to any of the setup options. Discard Changes Discard Changes done so far to any of the setup options. Restore Defaults Restore/Load Defaults values for all the setup options. 2808220 User’s Manual...
Page 54
Pressing ENTER causes the system to enter the OS. Launch EFI Shell from filesystem device Attempts to Launch EFI Shell application (Shellx64.efi) from one of the available filesystem devices. Reset System with ME disable Mode ME will run into the temporary disable mode. 2808220 User’s Manual...
LAN Drivers Installation ..............57 Intel® Management Engine Interface ..........60 IMPORTANT NOTE: After installing your Windows operating system (Windows 2000/ XP), you must install first the Intel Chipset Software Installation Utility before proceeding with the drivers installation. 2808220 User’s Manual...
1. Insert the CD that comes with the board. Click Intel and then Intel(R) QM57 Chipset Drivers. 2. Click Intel(R) Chipset Software Installation Utility. 3. When the Welcome screen to the Intel® Chipset Device Software appears, click Next to continue. 2808220 User’s Manual...
Page 57
4. Click Yes to accept the software license agreement and proceed with the installation process. 5. On the Readme File Information screen, click Next to continue the installation. 6. The Setup process is now complete. Click Finish to restart the computer and for changes to take effect. 2808220 User’s Manual...
To install the VGA drivers, follow the steps below. 1. Insert the CD that comes with the board. Click Intel and then Intel(R) QM57 Chipset Drivers. 2. Click Intel(R) QM57 Chipset Family Graphics Driver. 3. When the Welcome screen appears, click Next to continue. 2808220 User’s Manual...
Page 59
5. On the Readme File Information screen, click Next to continue the installation of the Intel® Graphics Media Accelerator Driver. 6. On Setup Progress screen, click Next to continue. 7. Setup complete. Click Finish to restart the computer and for changes to take effect. 2808220 User’s Manual...
1. Insert the CD that comes with the board. Click Intel and then Intel(R) QM57 Chipset Drivers. 2. Click Realtek High Definition Audio Driver. 3. On the Welcome to the InstallShield Wizard screen, click Next. 3. InstallShield Wizard is complete. Click Finish to restart the computer. 2808220 User’s Manual...
1. Insert the CD that comes with the board. Click Intel and then Intel(R) QM57 Chipset Drivers. 2. Click Intel(R) PRO LAN Network Driver. 3. When the Welcome screen appears, click Next. On the next screen, click Yes to to agree with the license agreement. 2808220 User’s Manual...
DRIVER INSTALLATION 4. Click the checkbox for Drivers in the Setup Options screen to select it and click Next to continue. 5. The wizard is ready to begin installation. Click Install to begin the installation. 2808220 User’s Manual...
Page 63
DRIVERS INSTALLATION 6. When InstallShield Wizard is complete, click Finish. 2808220 User’s Manual...
Microsoft .NET Framework 3.5 SPI should be first installed. Follow the steps below to install the Intel Management Engine. 1. Insert the drivers disc that comes with the motherboard. Click Intel and then Intel(R) AMT 6.0 Drivers. 2808220 User’s Manual...
Page 65
Management Engine Components, click Next. On the next screen, click Yes to to agree with the license agreement. 2. When the Setup Progress screen appears, click Next. Then, click Finish when the setup progress has been successfully installed. 2808220 User’s Manual...
Serial Port #2 IRQ4 Serial Port #1 IRQ5 Reserved IRQ6 Reserved IRQ7 Reserved IRQ8 Real Time Clock IRQ9 Reserved IRQ10 Serial Port #3 IRQ11 Serial Port #4 IRQ12 PS/2 Mouse IRQ13 80287 IRQ14 Primary IDE IRQ15 Secondary IDE 2808220 User’s Manual...
Page 73
Any advice or comments about our products and service, or anything we can help you with please don’t hesitate to contact with us. We will do our best to support you for your products, projects and business. Global American Inc. Address: 17 Hampshire Drive Hudson, NH 03051...