Operating The Unit Removing The Collected Water; Removing The Collected Water - Heat Controller R-410A Owner's Manual

Service Questions: Contact Comfort Aire at (517) 787-2100
Sales Inquiries: Contact Sylvane at (800) 934-9194 or visit sylvane.com
Heat Controller
OPERATING THE UNIT

Removing the collected water

There are two ways to remove collected water by empting the
bucket each time it's full or by continuously draining through
a hose into a drain.
1. Use the bucket
When the unit is off, if the bucket is full, the unit will beep 8 times
and the Full indicator light will flash, the digital display shows P2.
When the unit is on, if the bucket is full, the compressor turns off
and the fan turns off after 30 seconds for drying the water of the
condenser, then the unit will beep 8 times and the Full indicator
light will flash, the digital display shows P2.
Slowly pull out the bucket. Grip the handles securely, and
carefully pull out straight so water does not spill. Do not put
the tank on the floor because the bottom of the bucket is uneven,
which would cause the bucket to fall and the water to spill.
Throw away the water and replace the bucket. The
bucket must be in place and securely seated for the
dehumidifier to operate.
The machine will re-start when the bucket is restored
in its correct position.
NOTES:
When you remove the bucket, do not touch any parts
inside of the unit. Doing so may damage the product
or cause injury.
Be sure to push the bucket gently all the way into the
unit. Banging the bucket against anything or failing to
push it in securely may cause the unit not to operate.
When you remove the bucket, if there is some water in
the unit you must dry it .
2. Continuous draining
Water can be automatically emptied into a floor
drain by attaching the unit with a water hose
(Id¡ 5/16,not included))with a female threaded
end (ID:M=1 ,not included).
Install the drain hose onto the adaptor A (See Fig.7,
placed in the bucket).
Remove the plastic cover from the back drain outlet of
the unit and set aside and remove bucket, then insert
the drain hose through the drain outlet of the unit and
securely press it into the connector on the front of the
unit.(See.Fig.9)
Tighten the adaptor A and the unit by using two screws
(placed in the bucket).
Install the female threaded end of the water hose into
the adaptor A.(See.Fig.10),then lead the water hose
to the floor drain or a suitable drainage facility.
Make sure the hose is secure so there are no leaks.
Direct the hose toward the drain, making sure that
there are no kinks that will stop the water flowing.
Place the end of the hose into the drain and make sure
the end of the hose is level or down to let the water flow
smoothly.
Place the bucket back in the unit and make sure
that it is located correctly.
Select the desired humidity setting and fan speed
on the unit for continuous draining to start.
BHD-H Portable Dehumidifier
Connector
NOTE: When the continuous drain feature
is not being used, remove the drain hose
from the outlet.
8
1. Pull out the bucket a little.
2. Hold both sides of the bucket
with even strength, and pull it
out from the unit.
Fig.6
3. Pour the water out.
Drain hose
Adaptor A
Plastic cover
Drain hose
subassembly
Drain hose
Water hose
Female threaede
end
Owner's Manual
Care a
Turn th
from th
1. Clea
Use w
or abr
Do no
Fig.5
so ma
to dete
The a
a vacu
2. Clean
Every
mildew
and ad
empty
NOTE
After c
seated
3. Clean
Remo
operat
Remo
Fig.7
or to re
downw
Wash
Re-ins
CAUT
DO NO
Fig.8
becau
perform
4. When
After
the b
Clea
Wrap
Cove
Store
Fig.9
Fig.10