System Specifications; Receiver Specifications - Shure AXU Series User Manual

SYSTEM SPECIFICATIONS

Frequency Range:
(NOTE: Available frequen-
cies depend on applicable
regulations in country where
the system is used.)
Operating Range:
Audio Frequency
Response:
Image Rejection:
Spurious Rejection:
System Distortion
(ref. 45 kHz deviation,
1 kHz modulation):
Signal-to-Noise Ratio:
Maximum Recommended
Input Level, AXU1 (attenua-
tion switch at –20 dB, gain
at +32 dBV):
Minimum Recommended
Input Level, AXU1 (attenu-
ation switch at 0 dB, gain
at –80 dBV):
Operating Temperature
Range:
(NOTE: Battery characteris-
tics may limit range)
Transmitter Battery Life:
Connector:
Maximum Output Levels:
Nominal Output Levels:
Output
Configuration:
Actual Impedance:
Connector Pin
Assignments:
Dimensions:
Net Weight:
Power
Requirements:
Power Supply:
Voltage/Current/Phantom
Power Protection:
SPECIFICATIONS
Approximately 596 MHz to 862 MHz
100 m (approximately 300 ft.) under
typical conditions
20 to 16,000 Hz 3 dB
75 dB typical
75 dB typical
0.1% THD typical
90 dB
–110 dBm for 12 dB SINAD typical
-80 dB
7 to 38 C (45 to 100 ) F
12 hours with 9 V alkaline battery
(Duracell MN1604 recommended).

RECEIVER SPECIFICATIONS

3-Pin XLR (male)
Line Level: +10 dBV
Mic Level: –22 dBV
Line Level: –22 dBV
Mic Level: –46 dBV
Active Balanced
Line Level: 5.5 k
Mic Level: 500
Pin 1: ground
Pin 2: hot
Pin 3: cold
41 mm H x 197 mm W x 138 mm D (1.625 in. H x 7.77 in. W x 5.42
in. D)
419.6g (14.8 oz.)
12–18 VDC nominal, 200mA
120 V or 230V AC adaptor with 2.1 mm female plug
Yes
BODY-PACK TRANSMITTER SPECIFICATIONS
RF Output:
Input Configuration:
Connector Type:
Actual Impedance:
Connector Pin Assign-
ments:
Dimensions:
Net Weight:
Power Requirements:
Nominal Current Drain:
* Gain Control at minimum
** Gain Control at maximum
HAND-HELD TRANSMITTER SPECIFICATIONS
RF Output:
Dimensions:
Net Weight:
Power Requirement:
Nominal Current Drain:
1/4" phone plug (female)
+4 dBV
–26 dBV
Unbalanced
1 k
Tip: hot
Sleeve: ground
Yes
7
English
15 mW Typical
Unbalanced
4-pin Tini QG (male)
1 M
Pin 1:Tied to Ground
Pin 2:Tied to +5 V
Pin 3:Tied to Audio
Pin 4:Tied to 20k Resistor and
Audio Ground
82.6 mm H x 63.5 mm W x 26.2 mm
D
(3.25" H x 2.50" W x 1.03" D)
125g (4.4 oz.) including battery
9 V alkaline battery
(Duracell MN1604 recommended);
9 V lithium battery optional.
40 mA
15 mW Typical
241 mm H x 51 mm D
(9.49 in. H x 2.01 in. D)
296g (10.4 oz.)
9 V alkaline battery
(Duracell MN1604 recommended);
9 V lithium battery optional.
40 mA