InSinkErator C1300 Owner's Manual page 4

3
MOUNTING THE TANK
A
tank must be
mounted level
to ensure
proper operation.
NOTICE
1
2
Property Damage: tank must be located
within 16" of faucet and within 30" or less
of a standard grounded outlet. Do not extend
plumbing or electrical lines.
b
Leave 1/4" for
hanging tank.
3
1
2
1
Mount tank vertically in an area that
allows clearance on the underside of the
tank for drainage, if necessary.
DO NOT over tighten screws.
3
4
CONNECTING FAUCET TO TANK
A
(1) (2)
1
2
3
NOTICE
2
Property Damage: pinched or blocked water
lines may cause damage to the dispenser tank.
Check to make sure tubes are connected properly
and are pushed down as far as possible.
6
Select a spot under the sink to mount
tank vertically within reach of both
plumbing and electrical connections.
The tank should be within 16" or less
of faucet water lines and within 30"
or less of a standard grounded outlet.
While holding tank in place on
the spot selected for installation,
use a pencil to mark locations for
2 hanging screws.
Screws provided are for use in wood
Brass Nut
studs or cabinets only. Use wall anchors
(not supplied) for installation into drywall.
1
2
Pre-drill 1/8" pilot holes at marks.
Turn screws into pre-drilled holes,
leaving 1/4" exposed.
2
Hang the tank on the screws.
Tighten the screws with only
1/2 turn clockwise.
3
Without depressing the gray button,
place the snap-connect fitting at
(3)
2
3
the end of the blue 1/4" tube onto
the left fitting on the tank, pushing
until it clicks into place. (1)
Slip the flexible white 7/16" tube
over barbed middle fitting and slide
down approximately 1/2". (2)
Slip the clear 5/16" tube over the far
right smooth fitting and slide down
3
approximately 1/2". (3)
Visually check for pinched or
crimped tubes.
Hose clamps are not needed for any
of the connections.
1/4"
copper tube
5
FINAL WATER CONNECTION
A
Brass Nut
Brass Nut
Ferrule
Brass Insert
Brass Nut
1/4"
copper tube
Property Damage: Join remaining
tube to cold water supply only.
6
FILL TANK & THEN CONNECT POWER
Brass Nut
A
Brass Nut
Ferrule
Brass Nut
Brass Insert
Ferrule
Brass Insert
copper tube
1/4"
copper tube
Scalding Hazard: the faucet dispenses
near boiling (212ºF) water, which can
instantly cause scalds or burns. use care
when operating this appliance.
b
Property Damage: Do not use an extension
cord set with the dispenser. (a standard
grounded outlet within 30" of the dispenser is
NOTICE
Install a T-fitting (not included)
Ferrule
Brass Nut
Brass Insert
onto the cold water supply line.
Ferrule
Install dedicated water control valve
Brass Nut
Ferrule
Brass Insert Ferrule with 1/4" compression fitting.
1/4"
copper tube
At the end of the copper 1/4" tube,
1/4"
slide the fitting's brass nut and ferrule
copper tube
(not included) over the tube.
NOTICE
Insert the copper tube into the 1/4"
compression fitting and tighten.
Ferrule
Turn on the cold water supply.
Brass Nut
Brass Insert
Ferrule
Depress the dispenser handle and
Ferrule
hold it until water flows from the spout.
1/4"
Run the water for at least 2 minutes to
flush lines.
Check all connections to ensure they
are tight and that there are no leaks.
Plug in instant hot water tank.
To avoid permanent damage to the
product, only operate the tank after
it is filled with water.
Water will be cold at first.
NOTICE
Allow 12-15 minutes for water to reach
target temperature.
Gurgling or hissing is normal during the initial
required under the sink.)
heating cycle.
Personal Injury: This tank is a non-pressurized tank. DO NOT modify this system.
DO NOT close vent tube or connect other type dispensers or valves to the tank. Use
only the InSinkErator dispenser faucet supplied. Use only parts provided. Contact an
authorized InSinkErator Service agent for repairs or replacement components.
Fire Hazard: To minimize possibility of fire, DO NOT store flammable items such as
rags, paper or aerosol cans near the tank. DO NOT store or use gasoline or other
flammable vapors and liquids in the vicinity of this or any other appliance.
Property Damage: To avoid water damage, periodically inspect the unit for any
signs of leakage and immediately remove from service any unit suspected of
--
leaking and contact an authorized InSinkErator Service agent.
Brass Nut
Ferrule
Brass Nut
Ferrule
1/4"
copper tube
7