Vivotek FD8362 Quick Installation Manual
2mp, smart focus system, vandal-proof
Hide thumbs
Also See for FD8362:
- Specification (2 pages) ,
- User manual (196 pages) ,
- Quick installation manual (14 pages)
Table of Contents
Advertisement
Quick Links
Download this manual
See also:
User Manual
Advertisement
Table of Contents
Related Manuals for Vivotek FD8362
Summary of Contents for Vivotek FD8362
- Page 2 Warning Before Installation Power off the Network Camera as Refer to your user's manual for the soon as smoke or unusual odors are operating temperature. detected. Contact your distributor in the event of occurrence. Do not place the Network Camera on Do not touch the Network Camera unsteady surfaces.
-
Page 3: Package Contents
Package Contents FD8362/62E Mounting Plate Alignment Sticker / L-type Hex Key Wrench / Silica Gel / Ceiling Hole Template Sticker Screws / Hex Nut / DC Power Cable / Double-sided Tape Quick Installation Guide / Software CD Warranty Card Waterproof Connector & Bushing... -
Page 4: Physical Description
Physical Description Inner View Light Sensor Vari-focal Lens Black Cover Tilt Adjustment Screw Micro SD/SDHC Card Slot Jumpers Reset Button Microphone Video Output NTSC Internal 60Hz Audio/Video External 50Hz Out (green) Microphone In General I/O Terminal (pink) Block Ethernet 10/100 RJ45 Socket Heater NOTE: The heater is only available on... - Page 5 Outer View IP66-rated Vandal-proof Mounting Plate Dome Cover Record the MAC address under the camera base before installing the camera. Replace the side opening cover with the included side outlet bushing if you want to route cables from the side of camera. The 1/2"...
-
Page 6: Hardware Installation
Hardware Installation First, use the included T20 hex key wrench to loose the four screws and detach the dome cover from the camera base. Follow the steps below to install the camera either to a ceiling or a wall. IMPORTANT! Dome cover should be removed because if it should fall during the installa- tion process, physical injury could occur to your co-workers. - Page 7 Waterproof Connector Sealing Nut (A) Housing (B) Seals (C) Seal (D) Screw Nut (E) Hex Nut (F) Assembling Steps 1. Disassemble the components of the waterproof connector into parts (A) ~ (F) as shown above. waterproof connector (F --> E --> D --> B --> 2.
-
Page 8: Ceiling Mount
3. You will need an RJ45 crimping tool to attach the Ethernet wires to a connector. When done, connect the cable to the camera’s Ethernet RJ45 socket. o: white/orange stripe O: orange solid g: white/green stripe B: blue solid b: white/blue stripe G: green solid br: white/brown stripe BR: brown solid... -
Page 9: Wall Mount
Wall mount 1. Attach the supplied alignment sticker to the wall. 2. Using the circle marks on the sticker, drill at least 2 pilot holes symmetrically on each side into the wall. Then hammer the four supplied plastic anchors into the holes. 3. -
Page 10: Power Over Ethernet (Poe)
Network Deployment NOTE: 1. The DC power adaptor, if used, should General Connection (without PoE) comply with: O/P: 12V DC, 1.5A min., L.P.S. certified. 2. Pin #3 & 4 AC 24V as alternate power are for indoor use only Non-PoE Switch AC 24V±10% Pin 4 Pin 3... -
Page 11: Assigning An Ip Address
2. The program will conduct an analysis of your network environment. After your network is analyzed, please click on the “Next” button to continue the program. Installation Wizard 2 3. The program will search for VIVOTEK Video Receivers, Video Servers, and Network Cameras on the same LAN. EN - 10... -
Page 12: Ready To Use
Network Camera. 083236 00-02-D1-08-32-36 192.168.5.109 FD8362 0002D1083236 Ready to Use 1. A browser session with the Network Camera should prompt as shown below. 2. You should be able to see live video from your camera. You may also install the 32-channel recording software from the software CD in a deployment consisting of multiple cameras. -
Page 13: Adjusting The Lens
Adjusting the Lens Based on the live image retrieved from the camera, adjust the camera lens by doing the following: To adjust the viewing angle -- 3-axis mechanism design 1. Loosen the tilt adjustment screws and then turn the lens module up or down. Upon completion, tighten the screw.