Table of Contents Table of Contents 1. Before you Begin ......................1 What is Included ..........................1 Unpacking Instructions ........................1 Typographic Conventions ....................... 1 Icons Conventions .......................... 1 Safety Notes ........................... 2 Expected LED Lifespan ........................2 2. Introduction ........................3 Product Description ........................
Page 4
Table of Contents DMX Values ..........................15 TOUR ..............................15 BLOCK1 ..............................16 BLOCK2 ..............................16 ARC1 ..............................17 ARC1 + D ..............................17 ARC2 ..............................17 ARC2 + D ..............................17 ARC2 + S ..............................17 HSV ................................ 17 5.
Before you Begin 1. Before you Begin What is • One COLORado™ Batten 72 Tour • One power cord Included • One safety cable • Warranty Card • User Manual Unpacking Immediately upon receiving a fixture, carefully unpack the carton. Check the box or flight case contents to ensure that all parts are present and that they are in good Instructions condition.
There are no user serviceable parts inside the COLORado™ Batten 72 Tour. Any reference to servicing this unit you may find from now on in this User Manual will only apply to properly CHAUVET® certified technicians. Do not open the housing or attempt any repairs unless you are one of them.
Introduction 2. Introduction Product The COLORado™ Batten 72 Tour is RGBW linear LED wash light fixture. It consists of a single module that accommodates the internal power supply, the main control, the Description control panel, the LED drivers, the LED boards and lenses as well as the power and signal connectors.
Introduction DMX Channel Summary TOUR DMX Channel Function ARC1 DMX Channel Function Master Dimmer Green Green Blue Blue White ARC1 + D DMX Channel Function Amber Master Dimmer Macro + White Balance Strobe Green Auto Programs + Fan Blue Auto Speed Dimmer Speed ARC2 DMX Channel...
Introduction Product Overview Control Panel 5-Pin DMX In/Out 3-Pin DMX In/Out Safety Eye Bolt Fuse Power Out Power In Tilt Adjustment Knob Tilt Adjustment Knob COLORado™ Batten 72 Tour User Manual Rev. 01d August 23, 2010...
Setup 3. Setup AC Power The COLORado™ Batten 72 Tour has an auto-ranging power supply that can work with an input voltage range of 100~240 VAC, 50/60 Hz. Make sure that you are connecting this product to the proper voltage, as per the specifications in this guide, the product’s user manual or on the product’s sticker.
If you are not familiar with the DMX standard, or if you need information about the DMX cables needed to link the COLORado™ Batten 72 Tour fixture to a DMX controller, you may download the “DMX Primer” document from the CHAUVET® Web site. The DMX Channel Summary section in this chapter contains a brief description of what COLORado™...
COLORado™ Batten 72 Tour fixtures when using ID Addressing. If you are not familiar with the various connection methods when using ID Addressing, you may download the “DMX Primer” document from the CHAUVET® Web site. Mounting Read the safety notes at the beginning of this guide and follow their recommendations before mounting this product.
Operation 4. Operation Control Panel Button Function ONTROL ANEL Exits from the current menu or Description <MENU> function Enables the currently displayed <ENTER> menu or sets the currently selected value in to the current function Navigates upwards through the <UP> menu list and increases the numeric value when in a function.
Operation Continued from previous page DMX Control With ID In this mode, the fixtures with the same DMX starting address will respond to the DMX controller based on the fixture’s individual ID address setting. If the user selects ID Addressing address “0”, all the fixtures with the same DMX address will respond in unison.
Operation Continued from previous page Color Settings The COLOR setting determines how the COLORado™ Batten 72 Tour generates the white color based on various RGB settings. 1) Go to SETTINGS. 2) Select COLOR. 3) Select OFF, RGB TO W or UC. OFF = When RGB are all set to “255”, output is maximum.
Operation Continued from previous page Reset This setting allows the user to reset the COLORado™ Batten 72 Tour fixture to its default values, including the custom programs. 1) Go to SETTINGS. 2) Select RESET. 3) When prompted, enter the master access password as shown in Control Panel Lock.
Operation TOUR Notes These notes intent to clarify the way the TOUR DMX personality works. • Channel 1 controls the intensity of the currently projected color. Master Dimmer • When the slider is at the highest position (255) the intensity of the output is at its maximum.
Operation DMX Values Channel Function Value Percent/Setting TOUR 000 255 Dimmer 0~100% 000 255 0~100% (or Step Time if Custom 01~10 in Ch. 9 is active) 000 255 Green 0~100% (or Fade Time if Custom 01~10 in Ch. 9 is active) 000 ...
Operation Continued from previous page TOUR (Cont.) Channel Function Value Setting Value Setting Value Setting 000 009 All IDs ID 23 ID 46 010 019 ID 1 ID 24 ID 47 020 029 ID 2 ID 25 ID 48 030 ...
Operation Continued from previous page Channel Function Value Percent/Setting ARC1 000 255 0~100% 000 255 0~100% Green 000 255 0~100% Blue Channel Function Value Percent/Setting ARC1 + D 000 255 0~100% Master Dimmer 000 255 0~100% 000 ...
Dust build up reduces light output performance and can cause overheating. This can lead to reduced light source life and increased mechanical wear. CHAUVET® recommends cleaning the fixture’s external optics with a soft cloth using normal glass cleaning fluid.
Interference from AC wires Keep DMX cables separated from power cables or fluorescent/black lights If you still experience technical problems after trying the above solutions, contact CHAUVET® Technical Support. COLORado™ Batten 72 Tour User Manual Rev. 01d August 23, 2010 -19-...
Technical Information Exploded View Item Description Clear front plate Complete lens set LED board A LED board B Heat sink board Power supply Display board LED driver board Side cover Power output socket (white) Power input socket (blue) Fuse holder Support bracket -20- COLORado™...
The user must clearly label the package with a Return Merchandise Authorization Number (RMA #). CHAUVET® will refuse any product returned without an RMA #. DO NOT write the RMA # directly on the box. Instead, write it on a properly affixed label.
Technical Information Technical Specifications Weight & Dimensions Length ............................ 38.9 in (989 mm) Width ............................3.0 in (77 mm) Height ............................6.1 in (156 mm) Weight ............................9.8 lbs (4.4 kg) Power Auto-ranging ......................100~240 VAC, 50/60 Hz Power Consumption @ 120 V ....................72 W (1.067 A) Power Consumption @ 230 V ....................71 W (0.568 A) Inrush Current ....................
Page 28
CHAUVET® 5200 NW 108th Avenue Sunrise, FL 33351 (USA) (800) 762-1084 – (954) 929-1115 FAX (954) 929-5560 www.chauvetlighting.com COLORado™ Batten 72 Tour User Manual Rev. 01d August 2010...