Tripp Lite SmartPro Rackmount Owner's Manual
  1. Manuals
  2. Brands
  3. Tripp Lite Manuals
  4. UPS
  5. SmartPro Rackmount
  6. Owner's manual
Tripp Lite SmartPro Rackmount Owner's Manual

Tripp Lite SmartPro Rackmount Owner's Manual

Intelligent, line-interactive ups systems
Hide thumbs Also See for SmartPro Rackmount:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Owner's Manual
SmartPro
Intelligent, Line-Interactive UPS Systems
• 120V Sine-Wave Input/Output* • 500VA - 3000VA Capacities
* Except SMART500RT1U: sine-wave output on line; PWM output on battery.
Français
Copyright ©2004 Tripp Lite. All rights reserved. SmartPro
Owner's Manual
®
• Extended-Run Options
1111 W. 35th Street Chicago, IL 60609 USA
Customer Support: (773) 869-1234 • www.tripplite.com
Rackmount
®
is a registered trademark of Tripp Lite.
2
3
5
6
7
11
12
13
25

Advertisement

Table of Contents
loading

Related Manuals for Tripp Lite SmartPro Rackmount

Summary of Contents for Tripp Lite SmartPro Rackmount

  • Page 1: Table Of Contents

    Optional Installation Basic Operation Storage and Service Battery Replacement Español Français 1111 W. 35th Street Chicago, IL 60609 USA Customer Support: (773) 869-1234 • www.tripplite.com ® Copyright ©2004 Tripp Lite. All rights reserved. SmartPro is a registered trademark of Tripp Lite.

  • Page 2: Important Safety Instructions

    SAVE THESE INSTRUCTIONS This manual contains important instructions that should be followed during the installation, operation and storage of all Tripp Lite UPS Systems. Failure to heed these warnings will void your warranty. UPS Location Warnings • Use caution when lifting UPS. Because of the considerable weight of all Rackmount UPS systems, at least two people should assist in lifting and installing them.

  • Page 3: Mounting

    Mounting (Rack) Mount your equipment in either a 4-post or 2-post rack or rack enclosure (see next page for 2-post mounting). The user must determine the fitness of hardware and procedures before mounting. If hardware and procedures are not suitable for your application, contact the manufacturer of your rack or rack enclosure.
  • Page 4 Mount 1U UPS models in 2-post racks with included hardware following the procedure below. If you mount 2U UPS models in 2-post racks, they require the addition of a Tripp Lite 2-Post Rackmount Installation Kit (model: 2POSTRMKITWM, sold separately). See Installation Kit owner’s manual for installation procedure for 2U UPS models.

  • Page 5: Quick Installation

    Quick Installation Plug the UPS into an outlet on a dedicated circuit.* NOTE! after you plug the UPS into a live AC outlet, the UPS (in “Standby” mode) will automatically charge its batteries,** but will not supply power to its outlets until it is turned ON (see Step 3 below). * Select models include an additional plug which can be switched by a qualified electrician.

  • Page 6: Optional Installation

    (see ) to connect the communication port on your computer to the communication port of your UPS. Install on your computer the Tripp Lite PowerAlert Software appropriate to your computer’s operating system. Your UPS may feature additional communications ports; these ports may also be connected to additional computers which have PowerAlert Software installed.

  • Page 7: Basic Operation

    UPS batteries need to be recharged or replaced. Allow the UPS to recharge continuously for 12 hours, and repeat the self-test. If the LED remains lit, contact Tripp Lite for service. If your UPS requires battery replacement, visit www.tripplite.com to locate the specific Tripp Lite replacement battery for your UPS.

  • Page 8: Indicator Lights (Front Panel)

    UPS batteries need to be recharged or replaced. Allow the UPS to recharge continuously for 12 hours, and repeat the self-test. If the LED con- tinues to light, contact Tripp Lite for service. If your UPS requires battery replacement, visit www.tripplite.com to locate the specific Tripp Lite replace-...

  • Page 9: Ups Features (Rear Panel)

    USB connection to your UPS, you can remotely reboot connected equip- 15 amp/120V ment by turning the receptacles OFF and ON using Tripp Lite's PowerAlert NEMA 5-15R Software. Select models have their receptacles divided into one or more load banks (labelled “LOAD 1,”...
  • Page 10 UPS’s output can be evaluated without disrupting critical operations. External Battery Connector (Select Models Only): Use to connect Tripp Lite external battery packs for additional runtime. Refer to instructions available with the battery pack for complete connection information and safety warnings.

  • Page 11: Storage And Service

    2. If the problem continues, do not contact or return the UPS to the dealer. Instead, call Tripp Lite at (773) 869-1233. A service technician will ask for the UPS's model number, serial number and purchase date and will attempt to correct the problem over the phone.

  • Page 12: Battery Replacement

    Regulatory Compliance Identification Numbers For the purpose of regulatory compliance certifications and identification, your Tripp Lite product has been assigned a unique series number. The series number can be found on the product name- plate label, along with all required approval markings and information. When requesting compliance information for this product, always refer to the series number. The series number should not be confused with the marking name or model number of the product.

  • Page 13: Español

    1111 W. 35th Street, Chicago, IL 60609 USA 773.869.1234 (USA) • 773.869.1212 (International) www.tripplite.com 200503166 93-2406_EN...

This manual is also suitable for:

Smartpro rackmount smart500rt1u

Table of Contents