Download Print this page
Sonance LS47SAT Instruction Manual

Sonance LS47SAT Instruction Manual

Landscape series in-ground subwoofer
Hide thumbs Also See for LS47SAT:

Advertisement

Quick Links

9.50" (241mm)
I n s t r u c t I o n M a n u a l
sonance
landscape series
®
16.00" (406mm)
in-ground subwoofer
introduction
Thank you for purchasing sonance landscape series speakers.
when properly installed, these speakers will provide you with years
of outdoor entertainment pleasure. To get the most out of your new
speakers, please read this manual thoroughly before you begin
installation.

box contents

sonance landscape series in-ground subwoofer boxes contain:
(1) in-ground subwoofer
(1) dark brown canopy with abs tube
(1) rubber elbow
(2) stainless steel hose clamps
(2) silicon filled wire nuts
subwoofer location selection
The sonance landscape series is designed to deliver a seamless,
evenly dispersed sound field in an 'open air' environment. An array
of multiple satellite speakers and subwoofers should be strategically
placed to minimize 'hot spots' and 'nulls' as you move around the
outdoor entertainment area
As a general guideline, (1) Subwoofer will cover about
2000 square feet of listening area
figure 1 shows The sonance landscape series placed along the
perimeter of the entertainment area.
select a central location for the subwoofer if using only one subwoofer
(see figure 1) if using multiple subwoofers, select locations that are
the same distance from the main listening area.
figure 1
4.0" (102mm)
subwoofer
Amplifier Power Planning
The maximum number of satellites and subwoofers that can be
used in a system will depend on the quantity of amplifier power
available.
before beginning an installation use the chart below to calculate
the amplifier power your installation will require. Multiple
amplifiers may be required in large installations.
wattage calculator
model
qty. ch1 qty. ch2 x
ls47saT
ls67saT
ls67w
ls10sub
TOTAL MINIMUM WATTAGE
Amplifier Selection
for systems up to 500w per channel use the crown cdi 1000
for systems up to 800w per channel use the crown cdi 2000
for systems up to 1000w per channel use the crown cdi 4000
1
in-ground subwoofer
watts
total ch1
total ch2
x
25
x
25
x
25
x
100
total
20%
head
room

Advertisement

loading

Summary of Contents for Sonance LS47SAT

  • Page 1: Box Contents

    (2) stainless steel hose clamps (2) silicon filled wire nuts subwoofer location selection The sonance landscape series is designed to deliver a seamless, evenly dispersed sound field in an ‘open air’ environment. An array in-ground subwoofer of multiple satellite speakers and subwoofers should be strategically 4.0"...
  • Page 2: Subwoofer Installation

    2. dig the hole a minimum of 16”w x 26“l x 13” - 16”d. see to next speaker and so on. see figure 5 figure 2 Note: Sonance strongly recommends the use of 14 gauge, or larger, direct burial grade wire. 4”...
  • Page 3: Specifications

    Specifications ls10sub woofer: 10” (254mm) polypropylene cone with a rubber surround frequency response: 35Hz – 80Hz ±3db power required: 100 watts Enclosure Material: 1/2” (HDEP) Non-corrosive sealed enclosure crossover: 100Hz 9.50" (241mm) available finishes: black enclosure, dark brown Textured canopy dimensions: woofer enclosure 16.00"...
  • Page 4 SPECIFICALLY EXCLUDED. no one is authorized to make or modify any warranties on behalf of sonance. The warranty stated above is the sole and exclusive remedy and Sonance’s performance shall constitute full and final satisfaction of all obligations, liabilities and claims with respect to the Product.

This manual is also suitable for:

Ls67satLs67wLs10sub