Team Losi Mini-LST2 Operation Manual
  1. Manuals
  2. Brands
  3. Team Losi Manuals
  4. Motorized Toy Car
  5. Mini-LST2
  6. Operation manual

Team Losi Mini-LST2 Operation Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Operation Manual
Introduction
Thank you for purchasing the Mini-LST2 from Losi
®
. This guide contains the basic instructions for operating your
new Mini Monster Truck. While the Mini-LST2 is great for first-time R/C drivers, it does require some mechanical
experience and/or adult supervision for drivers under the age of 12. It is crucial that you read all of the instructions,
safety warnings, and accompanying printed material in order to operate your new model correctly and avoid
unnecessary damage. Please take a moment to look the documentation over before running your new Mini-LST2.

Advertisement

Table of Contents
loading

Related Manuals for Team Losi Mini-LST2

Summary of Contents for Team Losi Mini-LST2

  • Page 1 . This guide contains the basic instructions for operating your new Mini Monster Truck. While the Mini-LST2 is great for first-time R/C drivers, it does require some mechanical experience and/or adult supervision for drivers under the age of 12. It is crucial that you read all of the instructions, safety warnings, and accompanying printed material in order to operate your new model correctly and avoid unnecessary damage.

  • Page 2: Warranty Period

    Warning resulting damage or injury. By the act of use, setup or assembly, the user accepts all resulting liability. An R/C model is not a toy! If misused, it can cause serious bodily harm and damage to property. Operate If you as the Purchaser or user are not prepared only in open areas and follow all instructions included to accept the liability associated with the use of with your radio and model.

  • Page 3: Warranty Inspection And Repairs

    Electronics and engines requiring inspection or repair be operated with caution and common sense. Failure should be shipped to the following address: to operate your Mini-LST2 in a safe and responsible manner could result in damage to the model and Horizon Service Center property.

  • Page 4: Required Equipment

    #0 or #1 Phillips screwdriver • LOSA99100 .050˝ Allen Wrench Note: Use only Losi tools or other high quality tools. Use of inexpensive tools can cause damage to the small screws and parts used on this type of model. The Radio System The following is an overview of the various functions and adjustments found on the Losi DSM ®...

  • Page 5: The Transmitter

    Re-Binding the Transmitter to the Receiver The Losi DSM radio system included in the Mini-LST2 operates on 2.4 GHz, and provides 79 different channels which are automatically selected when the transmitter and vehicle are turned on. The communication between the transmitter and receiver begins in the few seconds after the transmitter and vehicle are both turned on.

  • Page 6: Chassis Tuning

    This is really helpful when you are on slick, as well as high traction, surfaces. If your Mini-LST2 turns too sharply and/or spins out easily, try turning the steering rate down by rotating the knob counterclockwise (to the left).

  • Page 7: Ride Height

    Changing the Pinion Gear/Gear Ratio You must always use the same spec of motor and size of pinion gear on both motors in the Mini-LST2. When you install hotter motors you may find it necessary to install smaller pinion gears to keep them from overheating. This is usually caused when you are running in a confined area where the motors are not allowed to rev freely.

  • Page 8: Setting The Gear Mesh

    Setting the Gear Mesh 1. Insert a small strip of common notebook paper between the pinion and spur gear by feeding it into the gears as you slowly turn the spur gear with your fingers. 2. Lightly push the motor in toward the spur (if the motor will not move freely, loosen the top screw slightly) until the pinion is resting solidly against the spur and tighten both mounting screws.
  • Page 9 Rebuilding the Front and Rear Differential The gears in the differential will wear over time. The same is true for the outdrives, driveshafts, and rear axles. We suggest using a small rag or paper towel to lay out the parts you remove to make it easier to reassemble. 1.
  • Page 10 Rebuilding the Center Transmission 1. Remove both gear cover screws (1). Remove both front top plate screws (2). 2. Remove both rear top plate screws. 3. Remove the four lower chassis plate screws (1). Remove the four lower chassis plate screws (2). 4.
  • Page 11 NOT threads inside the shock body. TIGHTEN yet! Note: Your Mini-LST2 comes with 30wt shock fluid from the factory. Step 7 Step 8 Turn the shock over and use a...

  • Page 12: Shock Assembly

    Canada Belgium Denmark France Finland Germany Italy Netherlands LOSB0952 Spain Sweden Ireland Australia ©2007 Losi, an exclusive brand of Horizon Hobby, Inc. 4105 Fieldstone Rd. Champaign, IL 61822 Customer Support 1-877-504-0233 www.horizonhobby.com www.losi.com 10625 Page 12...

Table of Contents