Attaching The Light Fixture - Hunter Ceiling Fans Installation And Operation Manual

8 8 8 8 8
attaching the decorative clamps
Your Hunter Fan comes with two decorative clamps: upper clamp
and lower clamp. Each clamp assembly is made up of two pieces.
1. Place the two halves of the lower clamp around the lower end
of the spindle and the motor adapter. See Figure 24.
Upper Clamps
Clamp Screws
Motor
F F F F F i i i i i g g g g g ur ur ur ur ure 24 - A e 24 - A e 24 - A e 24 - At t t t t t t t t t a a a a a c c c c c h h h h h in in in in ing d
e 24 - A
2. Insert two screws into the lower clamps and tighten to lock
the clamp into place. See Figure 24.
3. With the lower clamp in place, take both pieces of the upper
clamp and place them around the downrod and spindle. See
Figure 24.
4. Insert and tighten the two screws so that the upper clamp as-
sembly locks in place. See Figures 24 and 25.
F F F F F i i i i i g g g g g ur ur ur ur ure 25 - D e 25 - De e e e e c c c c c o o o o o r r r r r a a a a a t t t t t i i i i i v v v v v e c e 25 - D e 25 - D e 25 - D
41804-01 03/26/2003
Downrod
Spindle
Lower Clamps
g d g de e e e e c c c c c o o o o o r r r r r a a a a a t t t t t i i i i i v v v v v e c g d e c e cl l l l l a a a a a mp e c mp mp mps s s s s
g d e c mp
Upper Clamps
Lower Clamps
e c e c e cl l l l l a a a a a mp e c mp mp mp mps in s in s in s ins s s s s t t t t t a a a a a ll ll ll ll lle e e e e d d d d d s in

attaching the light fixture

1. Attach the support arms to the lower switch housing as shown
in Figure 26.
F F F F F i i i i i g g g g g ur ur ur ur ure 26 - A e 26 - A e 26 - At t t t t t t t t t a a a a a c c c c c h h h h h in in in in ing t e 26 - A g t g t g th h h h h e s
e 26 - A g t
s s s s s w w w w w i i i i i t t t t t c c c c c h h
2. Connect the upper plug connector from the motor to the lower
plug connector in the lower switch housing/light assembly. See
Figure 27.
Lower Plug
Connector
Housing Assembly Screws
F F F F F i i i i i g g g g g ur ur ur ur ure 27 - P e 27 - P e 27 - P e 27 - P e 27 - Plu lu lu lu lug c g co o o o o nn g c g c g c nne e e e e c c c c c t t t t t i i i i i o o o o o n a nn nn nn
in in in in ins s s s s t t t t t a a a a a ll ll ll ll lla a a a a t t t t t i i i i i o o o o o n n n n n
NOTE: Both plug connectors are polarized and will only fit
together one way. Make sure that both connectors are prop-
erly aligned before connecting them together. Incorrect con-
nection could cause improper operation and damage to the
product.
3. Place the lower switch housing assembly over the motor hous-
ing. Align the bottom screw holes in the motor and lower
switch housings. Attach the lower switch housing to the mo-
tor housing with three #6-32 housing assembly screws. See
Figure 1a.
4. Insert 3 - 40 Watt candelabra base light bulbs into the light
sockets. See Figure 27.
5. Place the glass bowl over the threaded rod.
6. Place the cap and finial over the threaded rod. Screw the finial
onto the threaded rod until tight.
7. Slide the support arms together until they are tight to the glass.
Support Arm
Assembly
Glass Bowl
Cap
Finial
e s e s e s e sup up up upp p p p p o o o o o r r r r r t a up t a t a t a t ar r r r r m m m m m s t s t s t s t s to t o t o t o th h h h h e l e l e l e l e lo o o o o w w w w w e e e e e r r r r r
o t
h h h ho o o o o u u u u u sin h h h h sin sin sin sing g g g g
Upper Plug
Connector
Lower Switch
Housing
n a n a n a n an n n n n d l d l d l d l d lo o o o o w w w w w e e e e e r s r s r s r s r sw w w w w i i i i i t t t t t c c c c c h h h ho o o o o u u u u u sin h h h h h h sing g g g g sin sin sin
© 2003 Hunter Fan Company