Table of Contents
Related Manuals for Graco Hydra-Clean 800-233
Summary of Contents for Graco Hydra-Clean 800-233
- Page 1 IPAPQRTANT This manual contains WARNINGS and 1NSTRUCTIONS READ AND RETAIN FOR REFERENCE 800-233 P I N SERIES "A" 1200 psi (82 bar) OPERATING PRESSURE BNC. GWACQ P.O. BOX 1441 MWINNEAPOILUS, W W M 554404 OCOPYRIGHT 1987 GRACO INC.
- Page 2 Gesaeual S a f e t y This pressure washer generates very high fluid pressure. Spray from the gun. leaks components can inject fluid through your skin and into your body and cause extremely serious bodily injury, including the need for amputation.
-
Page 3: Chemical Compatibility
HAZARD eapleoai Safeuy Any misuse of the pressure washer or accessories, such as overpressurizing, modifying parts, using incompatible chemicals and fluids, or using worn damaged parts, can cause them to rupture and result in fluid injection, splashing in the eyesor ontheskin, or other serious bodily injury or property damage. - Page 4 1. Remove the two hood bolts, flats and locks, from the center bottom of each side of the hood. Pivot the hood open. Position the handle into the end closest to the wheels. Line up the four mounting holes. Install the four outside of the chassis.
-
Page 5: Water Supply
10 minutes. -
Page 6: Injector Operation
Injector Operation C h e m i c a l sure 8. Be that the control ring on the injector is open t w o full turns from the check this, the hood must be opened. Once the control ring is open, may be left alone. -
Page 7: Maintenance
2. If the pressure washerwill beexposedtofreezing temperatures, drain you must store the pressure washer in freezing temperatures, flush it with a follow this solution. This can be done by placing the end of the inlet hose into a bucket of solution. -
Page 8: Troubleshooting Chart
TROUBLESHOOTING CHART. To reduce the risk of serious bodily injury, including fluid injection, injury from moving parts, always follow the Pressure Relief Procedure Warning on PROBLEM CAUSE Low Pressure Worn noale. Coupling slippage. Air leak in inlet plumbing. Inlet filter clogged. Worn packing. -
Page 9: Pump Service
PUMP SERVICE To reduce the risk of serious bodily injury, including fluid injection, splashing injury from moving parts, always follow the Pressure Relief Procedure Warning on page 7 before proceeding. NOTE: The following metric wrenches are needed: M 6 Allen wrench, M10, and M30. A pump repair tool kit, P/N 800-271, is available. - Page 10 4. Inspect the plunger shaft for oil crankcase. If leaking is obvious, replace the oil .seals (216). Otherwise, seals as they cannot be reused. NOTE: Oil Seal .Kit, part available to replace all three seals. Lightly grease the oil seal (if and the flinger, and replace them shaft.
-
Page 11: Parts Drawing
PARTS DRAWING 800-233 Hydra-Clean 1235, P/M (Continued) 802-777 11 .. -
Page 12: Wiring Diagram
PARTS DRAWING Hydra-Clean 1 2 35 WIRING DIAGRAM . ~ ..PARTS LIST Hydra-Clean 1235, P / N 8 0 0 - 2 3 3 REF. PART NO. NO. DESCRIPTION 1 802-760 COVER, Switch 2 801-892 CORD W/PLUG, 12/3 801-223... -
Page 13: How To Order Replacement Parts
REF. PART DESCRIPTION 801-009 QUICK COUPLER. Female (Includes 801-202 0-Ring) 22 801-090 QUICK COUPLER, Male 23 801-967 HOSE, 30 801-605 SCREW, 10-24 801-875 LOCK, #lo 801-546 BOLT, 3/8-16 FLAT, 5/16 28 801-015 29 801-363 LOCK, 3/8 801:214 BOLT, 3/8-16 801-813 TUBING, 1/4 I.D. -
Page 14: Repair Kits
PARTS DRAWING Pump, 802-629 PARTS LIST Pump, 802-629 REF. PART 801-651 801-652 $204 801 -470 $205 ,206 802-319 801-485 WASHER 4 8 4 CAP, 801 -482 1 /2 CAP, 801 -483 WASHER ". *211 HEAD RING t*212 PACKING *213 INTERMEDIATE RING *214 PACKING RETAINER *215... -
Page 15: Technical Data
V. 60 MOTOR 3 hp. single phase 230 WATER PUMP: 1200 psi (83 bar) measured at pump 3.5'GPM 113.3 liter/min) Bypass Hose: Synthetic yarn, EPDM Pressure Washer (including fitting): Anodized Aluminum, Aluminum Bronze alloys. Brass, Copper, PTFE PTFE PTFE PTFE Nylon- composite. - Page 16 THE GRACO WARRANTY WARRANTY Gram warrants all equipment manufactured by it and bearing material and workmanship the date of sale by an authorized Graco distributor to the original purchaser use. purchaser's twelve months from the date of sale. repair warranty applies only when the equipment is installed. operated and maintained in accordance Graco's written recommendations.