Contour; Level; Mic/Line Switch; Signal Indicator - Mackie SRM350v2 User Manual

4. CONTOUR

Pushing in this switch engages a filter that provides  dB
of boost to the low and high frequencies (below 100 Hz
and above 1 kHz). This provides a punchy, crisp sound
for most live music applications. You can experiment with
this switch by leaving it out for a while, then pushing it in
to determine which way sounds best for your application.
It is especially useful when listening at lower volumes, as
it highlights the bass like a Loudness switch, in addition to
boosting the highs.

5. LEVEL

This is used to adjust the signal level going into the
built-in power amplifiers, from off up to 5 dB of gain. Since
the SRM50v incorporates Mackie's world-class low-noise
mic preamp technology, you can connect either a line-level
or a microphone-level signal to the input, and use this con-
trol to adjust the level correctly.
There is no phantom power provided for a
microphone, so you should use a dynamic
mic, or use a condenser type if it has its own
battery power.
Follow the Quick Start guide on page 6 for setting the
LEVEL control. For most applications, it will be in the NOR-
MAL position (1 o'clock). If you have a particularly high
line-level signal connected to the SRM50v, you may need
to turn the control down to the 9 o'clock position. If you
have a low line-level or mic-level signal connected, you may
need to turn the LEVEL control up to the  o'clock position.
6. MIC/LINE Switch
Leave this switch out when connecting a line-level signal
to the INPUT connector (from a mixer, graphic EQ, or other
line-level signal source).
Push this switch in when connecting a microphone
to the INPUT connector. Since a microphone produces a
much smaller signal than a line-level signal, this provides
an additional 0 dB of gain to boost the microphone signal
to a line level.
7. SIGNAL Indicator
This LED illuminates whenever there is a signal present
at the INPUT connector on the rear panel. It senses the
signal just after the LEVEL control, so if the LEVEL control
is turned down, the SIGNAL indicator won't light.
8. LIMIT Indicator
When the signal levels at the amplifier outputs approach
clipping, a soft limiting circuit is activated that reduces
the input signal. The LIMIT LED lights whenever the limit
circuit is active.
It's okay for the LIMIT indicator to blink occasionally,
but if it blinks frequently or continuously, either turn down
the signal level at the mixer or other signal source, or turn
down the SRM50v's LEVEL control.
Wear hearing protection if you are close to
the SRM50v playing at high levels.
9. INPUT Connector
This is a combination female XLR-type and 1/" TRS
connector that accepts a balanced or unbalanced mic- or
line-level signal.
10. THRU Connector
This is a male XLR-type connector that can be used to
daisy-chain the input signal to another speaker.
The signal at this point is after the MIC/LINE switch but
before the LEVEL control. If you have a microphone con-
nected to the first SRM50v and you have the MIC/LINE
switch pushed in, the signal at the THRU jack is boosted
0 dB to a line-level, so leave the MIC/LINE switch out on
the next SRM50v.
ACTIVE SOUND REINFORCEMENT SYSTEM
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR
MOISTURE. DO NOT REMOVE COVER. NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL.
AVIS:
RISQUE DE CHOC ELECTRIQUE — NE PAS OUVRIR
SERIAL NUMBER MANUFACTURING DATE
SIGNAL
LIMIT
NORMAL
+45
O O
+5dB
LEVEL
100Hz 12k/AIR LINE
MIC
CONTOUR
POWER
(+3dB)
THRU
INPUT
9