Table of Contents
Advertisement
ENGLISH
1. Home Theater Playback - Playing on a Multi-channel System -
Using an HDMI Cable to Connect to an AV Amp or Television
• When connecting with an HOMI cable, press
[~)
and set it to "HOMI On",
• Your OBP-A100 automatically detects the audio/video signal supported by the connected HOMI
device and outputs the signal. To change the setting, see "HOMI Setup" on the GUI menu
(G"'page 23, 24).
'Nejia
• When you press
[~)
and set it to "HDMI On", no video signals are output from the component
video outputs.
• To disable video or audio output from the HDMI terminal. set the "Video Out" of the "Pure Direct
Setup", which outputs high quality analog audio, to "Off". To enable the HDMI signal output. set the
Pure Direct mode to one of the following settings:
• Pure Direct mode"Off" or "User Preset 1" or "User Preset 2"
('*)
("Playing Back High-Quality Audio (Pure Direct Function)" I125'page 38)
'*
Do this after setting "Pure Direct Setup" - "User Preset 1" or "User Preset 2" - "Video Out" on the
GUI menu to "On" (lI25'page 28).
With "HOMI On"
Audio/video signals are output from the HDMI terminal.
When the HDMI video resolution is set to ':Auto" as described in "HDMI Video Resolution Settings
"
(1125'
page 13), the DBP-A100 outputs the highest resolution video signal that is supported by the
connected equipment.
AVAmpor
/'
TV
lo~~ID
IE] ..
1
~
--_.,~
r~nO
HOMI
IN
U<§lg'<?
0
J""TEJ _. --,
~.!!
I
£§J~
~
0000
---
l=ul_el I
l
lINDt/I
...
~
....J
1-1
'NeJia
• When audio/video signals are output from the HDMI terminal, no video signals are output from the
component terminals.
• When a signal comprising 24 frames per second. such as 1080P24, is output from the HDMI terminal,
no video signals are output from the video or S-Video outputs.
With "HOMI Off"
Audio/video is not output from the HDMI terminal.
o
Connection to a device with a OVI-O terminal
If you use a HDMI/DVI-D conversion cable (sold separately), HDMI video signals are converted to DVI-
D signals, enabling connection to a device with a DVI-D terminal.
'NeOa
• In this case, the audio signal is not output. Make the appropriate audio connections for your devices.
(GT' page 14 - 20).
• The video signal will be in RGB format.
• You cannot output to a DVI-D device that does not support HDCP (high-bandwidth digital content
copyright protection system).
• Video may not be output depending on the combination of devices.
I
Required Settings for HDMI Connection
Setting HOMI Video Output
o
Make HOMI Output Signal and HOMI Control Function Settings
"HDMI Setup" (GT'page 23, 24)
o
Make the Video Output Signal Setting for the Connected Television
"Video Setup" (m::Fpage 24)
o
HOMI Video Resolution Settings
RESOllJTlON
• Change the HDMI video resolution by pressing
[~.
Switch the output mode as follows. The default
settings is underlined.
[
Auto
Source Direct -
480/576i
- -
480/576P
:J
(Auto)
(Source direct)
(480/576 interlaced)
(480/576 progressive)
1080P24
1080P
1080i
720P
(1080 progressive, 24-frame)
(lOBO
progressivel
(lOBO
interlaced)
(720 progressive)
'If the HDMI resolution is not set to "Auto", set it to correspond with the resolution of your television.
Images will not be projected normally if the television resolution and DBP-A 100's output resolution do
not match.
• Audio and video will be temporarily interrupted if the power of the connected device currently playing
is turned off, or the input is switched.
'When you change the HDMI video resolution of the DBP-A100, it takes a few seconds up to about 10
seconds for validation between the DBP-A100 and the connected device. Audiolvideo is not output
during this period.
• When outputting deep colour or 1080p, etc., we recommend you use a High Speed HDMI cable for
enhanced high-quality playback.
f'.~
.'i:i1
When outputting a video signal comprising 24 frames per second from the HDMI terminal. select
"1080P24" or "Source Direct" after setting the GUI menu "HDMI Setup" - "lIP Direct" (G"'page 23) to
"On".
I
See overleaf>
13
I
Advertisement
Table of Contents
