Specifications - Jacuzzi K272000AF Installation And Operating Instructions Manual

Important: Read complete instructions before beginning installation.
Each whirlpool bath arrives ready for installation, completely equipped with motor/pump assembly and plumbing and fittings
necessary for whirlpool operation. An optional drain/overflow kit is available for installation on the bath.
Remove the bath from the carton. Retain the shipping carton until satisfactory inspection of the product has been made. Do
not lift the bath by the plumbing at any time; handle by the shell only.
Immediately upon receipt, inspect the shell before installing. Should inspection reveal any damage or defect in the finish, do
not install the bath. Damage or defect to the finish claimed after the bath is installed is excluded from the warranty. Jacuzzi
Whirlpool Bath responsibility for shipping damage ceases upon delivery of the products in good order to the carrier. Refer any
claims for damage to the carrier. For definitions of warranty coverage and limitations, refer to the published warranty informa-
tion packed with the product.
All bath units are factory tested for proper operation and watertight connections prior to shipping. NOTE: Prior to installa-
tion, the bath must be filled with water and operated to check for leaks that may have resulted from shipping damage
or mishandling. Jacuzzi Whirlpool Bath is not responsible for any defect that could have been discovered, repaired, or
avoided by following this inspection and testing procedure.
Not all tubs shown may be available as export units. Export tubs come with MANUAL controls and may come:
• with Pump/motor packaged
• with Pump/motor installed,
• with NO overflow cutout.
Because of the variety of export tub types some instructions may not apply to your unit. Disregard instructions that do not
apply to your specific tub.
RECTANGULAR BATHS
L
(51 mm)
SIDE VIEW
BATHS WITHOUT INTEGRAL SKIRT
L
SIDE VIEW
BATHS WITH 3-SIDED TILE FLANGE

SPECIFICATIONS

(Rectangular) LH = Left Hand, RH = Right Hand
MODEL DIMENSIONS
AMIGA™
72" (1829 mm) L
36" ( 914 mm) W
LH & RH
20-3/4" ( 533 mm) H
AMIGA™
72" (1829 mm) L
WITH INTEGRAL
36" ( 914 mm) W
SKIRT
20-3/4" ( 533 mm) H
LH & RH
©
BIANCA
72" (1829 mm) L
48" (1219 mm) W
LH
20-1/2" ( 521 mm) H
©
CETRA
60" (1524 mm) L
WITH INTEGRAL
32" ( 813 mm) W
SKIRT
20-1/2" ( 521 mm) H
LH & RH
CETRA © 532
60" (1524 mm) L
31-7/8" ( 791 mm) W
LH & RH
21-1/4" ( 553 mm) H
©
CETRA 536
60" (1524 mm) L
36" ( 914 mm) W
LH & RH
21-1/4" ( 553 mm) H
*Add 1/4" (6,4 mm) to this dimension when roughing-in for 3-wall niche.
NOTE: The overall dimensions are nominal with a tolerance of +0 and -1/4" (6,4 mm).
FOR ALL UNITS: Electrical Service Requirements: All require a dedicated GFCI protected separate circuit.
(Optional) RapidHeat : 115 VAC, 15 AMP, 60 Hz. dedicated GFCI protected separate circuit.
TM
Motor/Pump: 115 VAC, 15 Amp, 60 Hz. dedicated GFCI protected separate circuit.
SPECIFICATIONS
,
separately
W
2"
H
END VIEW
(25 mm)
W
1"
H
END VIEW
DRAIN/OVERFLOW TOTAL WEIGHT/
CUTOUT
DIMENSIONS FLOOR LOADING
* 70" x 34"
16-7/8" (429 mm) A
(1778 mm x
14" (356 mm) B
864 mm)
* NA
16-7/8" (429 mm) A
14" (356 mm) B
* 16" (406 mm) A 70" x 46"
8-1/2" (216 mm) B (1778 mm x
1168 mm)
* 17-7/8" (454 mm) A NA
9-3/8" (238 mm) B
* 58" x 30-1/4"
18-1/2" ( 470 mm) A
(1473 mm x
9" ( 229 mm) B
768 mm)
* 58" x 34-1/4"
18-1/2" ( 470 mm) A
(1473 mm x
9" ( 229 mm) B
870 mm)
L
SIDE VIEW
BATHS WITH INTEGRAL SKIRT
A
DRAIN/OVERFLOW
OPERATING PRODUCT
GALLONAGE WEIGHT
772 lb 50 U.S. gal 105 lb
(351 kg)/ (186 liters)
(48 kg)
43 lb/ft
2
(210 kg/m 2 )
50 U.S. gal
796 lb 129 lb
(186 liters)
(362 kg)/ (59 kg)
44 lb/ft 2
(214 kg/m 2 )
73 U.S. gal
993 lb 135 lb
(276 liters)
(451 kg)/
(61 kg)
41 lb/ft 2
(200 kg/m 2 )
46 U.S. gal
727 lb 94 lb
(330 kg)/ (174 liters) (43 kg)
55 lb/ft
2
(268 kg/m )
2
43 U.S. gal
697 lb 89 lb
(163 liters)
(317 kg)/ (41 kg)
53 lb/ft
2
(259 kg/m )
2
48 U.S. gal
742 lb 92 lb
(337 kg)/ (181 liters) (42 kg)
50 lb/ft 2
(244 kg/m 2 )
5
Jacuzzi Whirlpool Bath K272000AF 7/06
(25 mm)
W
1"
H
END VIEW
B
HEATER READY
FOR FIELD
SKIRT &
INSTALLATION
MOUNTING
Yes
Optional,
(S750000 HEATER KIT)
U-Frame
Integral
Yes
(S750000 HEATER KIT)
Yes
Optional,
(S750000 HEATER KIT)
U-Frame
Integral Yes
(S750000 HEATER KIT)
Yes
Optional
(S750000 HEATER KIT)
U-Frame
Optional
Yes
U-Frame (S750000 HEATER KIT)