6 . 2
6 . 2
6 . 2
Internal connectors
Internal connectors
Internal connectors
6 . 2
6 . 2
Internal connectors
Internal connectors
This section describes and illustrates the internal connectors on the
motherboard.
1 .
1 . 1 .
F l o p p y d i s k d r i v e c o n n e c t o r ( 3 4 - 1 p i n F L O P P Y )
F l o p p y d i s k d r i v e c o n n e c t o r ( 3 4 - 1 p i n F L O P P Y )
1 .
1 .
F l o p p y d i s k d r i v e c o n n e c t o r ( 3 4 - 1 p i n F L O P P Y )
F l o p p y d i s k d r i v e c o n n e c t o r ( 3 4 - 1 p i n F L O P P Y )
F l o p p y d i s k d r i v e c o n n e c t o r ( 3 4 - 1 p i n F L O P P Y )
This connector supports the provided floppy drive ribbon cable. After
connecting one end to the motherboard, connect the other end to the
floppy drive. (Pin 5 is removed to prevent incorrect insertion when using
ribbon cables with pin 5 plug).
PTGD1-LA
PTGD1-LA Floppy Disk Drive Connector
2 . 2 .
2 .
2 .
I D E c o n n e c t o r ( 4 0 - 1 p i n I D E )
I D E c o n n e c t o r ( 4 0 - 1 p i n I D E )
I D E c o n n e c t o r ( 4 0 - 1 p i n I D E )
2 .
I D E c o n n e c t o r ( 4 0 - 1 p i n I D E )
I D E c o n n e c t o r ( 4 0 - 1 p i n I D E )
This connector supports the provided UltraDMA100/66 IDE hard disk
ribbon cable. Connect the cable's blue connector to the IDE connector,
then connect the gray connector to the UltraDMA100/66 slave device
(hard disk drive) and the black connector to the UltraDMA100/66 master
device.
•
Pin 20 on the IDE connector is removed to match the covered hole
on the UltraDMA cable connector. This prevents incorrect orientation
when you connect the cables.
•
The hole near the blue connector on the UltraDMA100/66 cable is
intentional.
PTGD1-LA
PTGD1-LA IDE Connector
A S U S P T G D 1 - L A ( G r o u p e r - G L 8 E ) m o t h e r b o a r d
A S U S P T G D 1 - L A ( G r o u p e r - G L 8 E ) m o t h e r b o a r d
A S U S P T G D 1 - L A ( G r o u p e r - G L 8 E ) m o t h e r b o a r d
A S U S P T G D 1 - L A ( G r o u p e r - G L 8 E ) m o t h e r b o a r d
A S U S P T G D 1 - L A ( G r o u p e r - G L 8 E ) m o t h e r b o a r d
PIN 1
FLOPPY
NOTE: Orient the red markings on
the floppy ribbon cable to PIN 1.
NOTE: Orient the red markings
(usually zigzag) on the IDE
ribbon cable to PIN 1.
PIN 1
1 1
1 1
1 1
1 1
1 1