Table of Contents
Advertisement
Quick Links
Use these instructions to install the Garmin
of this package with the packing list on the box. If any pieces are missing, contact your Garmin dealer immediately.
Use the following instructions to install the AIS 300 device. Details for the following steps are included in this document:
1. Select locations for the AIS components.
2. Mount the AIS 300 receiver box.
3. Connect the AIS 300 to power.
4. Connect the AIS 300 to a VHF antenna and to an optional VHF radio
5. Connect the AIS 300 to a NMEA 2000 network or to a NMEA 0183-compatible chartplotter (optional -
When navigating, carefully compare information provided by the unit to all available navigation sources, including information from visual
sightings, local waterway rules and restrictions, and maps. For safety, always resolve any discrepancies or questions before continuing
navigation.
Use this unit only as a navigational aid. Do not attempt to use the unit for any purpose requiring precise measurement of direction, distance,
location, or topography.
Wear safety goggles and a dust mask when drilling, cutting, or sanding.
Safe Compass Distance
Ensure that you install the AIS 300 receiver box at least 15
correctly when the AIS 300 is operating.
Selecting Locations for the AIS 300 Components
Use the wiring layout diagrams starting on
cables reach all components before permanently mounting any component.
Mounting the AIS 300 Receiver Box
Install the AIS 300 receiver box below deck on a bulkhead. Select a location that is dry and protected from washdown. Ensure that the
location is well ventilated and away from objects that generate heat. Ensure that the receiver box is at least 15
compass to avoid interference.
Needed tools
• Drill and drill bits
• Number 2 Phillips screwdriver
to mount the receiver box:
1. Ensure that the chosen location is dry, protected from washdown, and well-ventilated.
2. Use the receiver box as a template, and use a pencil to mark the holes in the four corners. Do not drill through the receiver box.
3. Drill four
/
in. (3 mm) pilot holes.
1
8
4. Mount the receiver box using the included 20 mm M 3.5 screws. You can also use bolts, washers, and nuts (not included) to mount the
receiver box if the mounting surface is suitable.
September 2013
AIS 300 Installation Instructions
AIS 300 Automatic Identification System (AIS) Class B receiver device. Compare the contents
®
WARNING
CAutIoN
/
in. (40 cm) from any compass. Test your compass to verify that it operates
3
4
page 2
to determine how to best organize the AIS 300 components on your boat. Ensure that the
190-01178-00 Rev. D
(page
4).
page
4).
/
in. (40 cm) from any
3
4
Printed in China
Advertisement
Table of Contents
Related Manuals for Garmin AIS
Summary of Contents for Garmin AIS
- Page 1 Mounting the AIS 300 Receiver Box Install the AIS 300 receiver box below deck on a bulkhead. Select a location that is dry and protected from washdown. Ensure that the location is well ventilated and away from objects that generate heat. Ensure that the receiver box is at least 15 in.
- Page 2 (optional - not included) 12 or 24 Vdc * The AIS 300 does not need to be installed alongside a VHF radio, but they can share the same VHF antenna if they are both installed on your boat. AIS 300 Installation Instructions...
- Page 3 (optional - not included) 12 or 24 Vdc * The AIS 300 does not need to be installed alongside a VHF radio, but they can share the same VHF antenna if they are both installed on your boat. ** The listed wire colors are for the NMEA 0183 Port 1 input on a Garmin GPSMAP 4000/5000 or GPSMAP 6000/7000 series chartplotter.
- Page 4 To transmit and receive AIS information, the AIS 300 must be connected to a VHF antenna (not included). Connect a marine VHF antenna to the AIS 300 using the antenna port on the device. If you have a VHF radio on your boat, connect the...
- Page 5 3. Consult the diagram below to connect the AIS 300 to a non-Garmin chartplotter. Use 22 AWG wire for extended runs of NMEA 0183 wire, if needed. If it is necessary to extend the power wires, use 16 AWG or larger wire.
-
Page 6: Specifications
Contact Garmin Contact Garmin Product Support if you have any questions while using the AIS 300. In the USA, go to www.garmin.com/support, or contact Garmin USA by phone at (913) 397.8200 or (800) 800.1020. In the UK, contact Garmin (Europe) Ltd. by phone at 0808 2380000. -
Page 7: Industry Canada Compliance
Limited Warranty This Garmin product is warranted to be free from defects in materials or workmanship for one year from the date of purchase. Within this period, Garmin will, at its sole option, repair or replace any components that fail in normal use. Such repairs or replacement will be made at no charge to the customer for parts or labor, provided that the customer shall be responsible for any transportation cost. - Page 8 Distributor warranties are only valid in the area of intended distribution. Devices purchased in the United States or Canada must be returned to the Garmin service center in the United Kingdom, the United States, Canada, or Taiwan for service.