Table of Contents
Advertisement
REMOTE
INPUT
OUTPUT
SOUND
CONTROL
INPUT
Sweeper Beam LED
of the cable. Also remember that DMX cable must be daisy chained
and cannot be split.
Notice:
Be sure to follow figures two and three when making your own
DMX512
cables. Do not use the ground lug on the XLR connector. Do not con-
DMX+,DMX-,COMMON
nect the cable's shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR's outer casing. Grounding
the shield could cause a short circuit and erratic behavior.
DMX512 OUT
3-PIN XLR
XLR Male Socket
1 Ground
2 Cold
2 Cold
REMOTE
INPUT
OUTPUT
CONTROL
INPUT
3 Hot
Figure 3
Special Note: Line Termination.
POWER
used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is con-
nected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ part number Z-DMX/T) will decrease the possibilities of erratic
behavior.
Termination reduces signal errors and
avoids signal transmission problems
1
1
DMX512 IN
and interference. It is always advisable
3
3
3-PIN XLR
to connect a DMX terminal, (Resistance
2
2
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
ADJ Products, LLC - www.adj.com - Sweeper Beam LED User Manual Page 7
SOUND
POWER
COMMON
DMX +
1
1
DMX512 IN
3
3
3-PIN XLR
DMX -
2
2
XLR Female Socket
XLR Pin Configuration
1 Ground
Pin 1 = Ground
REMOTE
INPUT
OUTPUT
SOUND
CONTROL
Pin 2 = Data Compliment (negative)
INPUT
3 Hot
Pin 3 = Data True (positive)
When longer runs of cable are
Figure 4
REMOTE
INPUT
OUTPUT
SOUND
CONTROL
INPUT
Set Up
Sweeper Beam LED
5-Pin XLR DMX Connectors.
512 data cables for DATA transmission in place of 3-pin. 5-pin DMX
fixtures may be implemented in a 3-pin DMX line. When inserting stan-
POWER
dard 5-pin data cables in to a 3-pin line a cable adaptor must be used,
these adaptors are readily available at most electric stores. The chart
below details a proper cable conversion.
Termination reduces signal errors and
avoids signal transmission problems
1
and interference. It is always advisable
3
Data Compliment (- signal)
to connect a DMX terminal, (Resistance
2
120 Ohm 1/4 W) between PIN 2 (DMX-)
Figure 2
and PIN 3 (DMX +) of the last fixture.
Sweeper Beam LED
The unit should be mounted using a mounting clamp (not provided),
affixing it to the mounting bracket that is provided with the unit.
Always ensure that the unit is firmly fixed to avoid vibration and slip-
ping while operating. Always ensure that the structure to which you
are attaching the unit is secure and is able to support a weight of 10
POWER
times the unit's weight. Also, always use a safety cable that can hold
12 times the weight of the unit when installing the fixture.
The equipment must be installed by a professional, and it must be
installed in a place where it is out of the reach of people's grasp.
ADJ Products, LLC - www.adj.com - Sweeper Beam LED User Manual Page 8
REMOTE
INPUT
OUTPUT
CONTROL
INPUT
Some manufactures use 5-pin DMX-
POWER
3-Pin XLR to 5-Pin XLR Conversion
Conductor
3-Pin XLR Female (Out)
Ground/Shield
Pin 1
Pin 2
Data True (+ signal)
Pin 3
Not Used
Not Used
Set Up
5-Pin XLR Male (In)
Pin 1
Pin 2
Pin 3
Pin 4 - Do Not Use
Pin 5 - Do Not Use
Installation
Advertisement
Table of Contents
